MacVap Posted November 11, 2016 Report Share Posted November 11, 2016 I did that before (install over), but this version is too different from what I have (I unpacked it and compared them). The driver is also different, so I want to uninstall the driver first, in order not to end up with two different drivers.I received a DNA 75 so I need a solid version that can work with both DNA's I have (the other is DNA 200). Link to comment Share on other sites More sharing options...
James Posted November 12, 2016 Report Share Posted November 12, 2016 Hello MacVap,We moved to a CDN for our downloads, since the traffic is into the terabytes... I've contacted them and will let you know what I find out.James Link to comment Share on other sites More sharing options...
James Posted November 12, 2016 Report Share Posted November 12, 2016 I've posted up 1.2 SP5. Please let me know if you run into any issues with it.Have a good night. James Link to comment Share on other sites More sharing options...
Spirometry Posted November 12, 2016 Report Share Posted November 12, 2016 SP5 appears to have fixed my charging issue on the Vaporshark. Link to comment Share on other sites More sharing options...
MacVap Posted November 12, 2016 Report Share Posted November 12, 2016 Hi James,I couldn't download SP5 too. I succeeded through a web proxy - it was quick and without delays. So it's definitely blocking my IP address.My IP address is [got it, thanks] (replace the letter O with zero, and the letters S with fives).Daniel Link to comment Share on other sites More sharing options...
James Posted November 12, 2016 Report Share Posted November 12, 2016 Could you try a traceroute (tracert evolvapor-downloads.r.worldssl.net on a command line)? Also to downloads.evolvapor.com? Thanks!(Does your country censor Internet? The CDN would share an IP address with many other sites. Also, what IP address does your PC think that site is? Lastly, do you have any plugins in your browser/firewall that might block sites?) Link to comment Share on other sites More sharing options...
MacVap Posted November 12, 2016 Report Share Posted November 12, 2016 P.M. sent to James. Traceroute completed successfully.The answer to most of these questions is no, there is no censorship and I don't have any unusual firewalls/browser plugins. In fact, I turned the firewall off for the testing, the behavior is exactly the same. And I tested with several browsers: IE, Firefox, Chrome, Opera.What struck me as odd is the behavior I haven't seen before, no response whatsoever, all browsers just keep on waiting and timeout sooner or later. Link to comment Share on other sites More sharing options...
Mgeli Posted November 13, 2016 Report Share Posted November 13, 2016 Hi. After upgrading to 1.2 SP5, can't log in to my account and Escribe to obtain information about my mod. Link to comment Share on other sites More sharing options...
retird Posted November 13, 2016 Report Share Posted November 13, 2016 Mgeli said:Hi. After upgrading to 1.2 SP5, can't log in to my account and Escribe to obtain information about my mod.Yep, same here and others say the same.... Evolv will get it fixed.... it may have to do with Evolv recently moving to a CDN for their downloads, since the traffic was getting kind of high. At least that's my guess....A content delivery network (CDN) is a system of distributed servers (network) that deliver webpages and other Web content to a user based on the geographic locations of the user, the origin of the webpage and a content delivery server. Link to comment Share on other sites More sharing options...
Mgeli Posted November 13, 2016 Report Share Posted November 13, 2016 Thanks for the reply Retird.....waiting for the decision.... Link to comment Share on other sites More sharing options...
Yellowhorse Posted November 13, 2016 Report Share Posted November 13, 2016 Mgeli said:Hi. After upgrading to 1.2 SP5, can't log in to my account and Escribe to obtain information about my mod.I am having the exact same problem. Waiting patiently for a solution. Link to comment Share on other sites More sharing options...
Modbustersecig Posted November 13, 2016 Report Share Posted November 13, 2016 Please help me Figure out why i cant log on in Escribe!!!!! Link to comment Share on other sites More sharing options...
James Posted November 13, 2016 Report Share Posted November 13, 2016 Fixed. Thanks for reporting that. Link to comment Share on other sites More sharing options...
dwcraig1 Posted November 13, 2016 Report Share Posted November 13, 2016 Gee, got to be 10:30 PM Ohio time Saturday night......James was still working. Kudos to James. Link to comment Share on other sites More sharing options...
Modbustersecig Posted November 13, 2016 Report Share Posted November 13, 2016 Thanks James, its working now. Link to comment Share on other sites More sharing options...
txmonkey214 Posted November 13, 2016 Report Share Posted November 13, 2016 The phantom 3rd cell on my VT133 disappeared after I applied sp5. What other bug fixes are addressed? Link to comment Share on other sites More sharing options...
Modbustersecig Posted November 13, 2016 Report Share Posted November 13, 2016 Modbustersecig said:Please help me Figure out why i cant log on in Escribe!!!!! thank you thank you James. I was in the middle of building a couple Opus DNA 250 the board is totally awesome. didn't realize it last night but it will still charge 1 amp when hooked to my PC same courd same pc .5 on the DNA200. I did get a full 2 amps out of it on the wall charger . took about 20 minutes to charge battery from 50% too 100% .while we were exploring the board on the first build on E scrib the battery was charged . you the man thank you James and Brandon Nick John Roger for the Opus the post man for delivering the best board ever.I Like it Link to comment Share on other sites More sharing options...
fwa Posted November 14, 2016 Report Share Posted November 14, 2016 Hello,Just apply the new SP5 on my DNA200 which have always before the 0% level of charge problem.After applying this service pack, the level seems to work again. Correction seems well working Link to comment Share on other sites More sharing options...
VapingBad Posted November 14, 2016 Report Share Posted November 14, 2016 fwa said:Hello,Just apply the new SP5 on my DNA200 which have always before the 0% level of charge problem.After applying this service pack, the level seems to work again. Have you corrected effectively this problem ?They have indeed, it was a problem that was only introduced with the early versions of 1.2, a side effect of other changes that should no be consigned to history. Link to comment Share on other sites More sharing options...
fwa Posted November 14, 2016 Report Share Posted November 14, 2016 VapingBad said:They have indeed, it was a problem that was only introduced with the early versions of 1.2, a side effect of other changes that should no be consigned to history.Ok, but it seems that we have another problem now. Voltage on the 3 cells is correct, but the level is very strange. When i check on my battery curve in the mod section, 3.63V is about 35.8% so why is it indicated 14% ? Link to comment Share on other sites More sharing options...
VapingBad Posted November 14, 2016 Report Share Posted November 14, 2016 I would wait for a charge cycle as it is not just the voltage that the battery gauge uses on the 200 and 250 they also track the usage like mobile phones do. Link to comment Share on other sites More sharing options...
Spector NS5 RD Posted November 14, 2016 Report Share Posted November 14, 2016 fwa said:Ok, but it seems that we have another problem now. Voltage on the 3 cells is correct, but the level is very strange. When i check on my battery curve in the mod section, 3.63V is about 35.8% so why is it indicated 14% ? 14% of 28.05 watt hours is 3.927 watt hours. that is very close to your remaining 3.814 charge estimate in device monitor, so that seems correct. can't say why at 3.63v it doesn't reflect 35.8%. however, 14% sounds more accurate than 35.8%, looking at your charge estimate. i'm not even positive if my math is correct. Link to comment Share on other sites More sharing options...
fwa Posted November 14, 2016 Report Share Posted November 14, 2016 ChunkyButt200 said:14% of 28.05 watt hours is 3.927 watt hours. that is very close to your remaining 3.814 charge estimate in device monitor, so that seems correct. can't say why at 3.63v it doesn't reflect 35.8%. however, 14% sounds more accurate than 35.8%, looking at your charge estimate. i'm not even positive if my math is correct.So if i follow your mind, now the level does not reflect the level of the battery reflecting his voltage but now the capacity.Ok, let's try, i am now at 20% 5675 Wh. So 100% = 5 x 5675 = 28375Wh, which seems correct. It is really strange that before the update, the level reflect exactly the reference of the battery csv. I have always used this to charge at 3.8V per cell my box for storage. I do this for my RC models as for my box .I must simply change my reference observing the charge for my different box, regarding what is the Wh at 3.8v Link to comment Share on other sites More sharing options...
fwa Posted November 14, 2016 Report Share Posted November 14, 2016 fwa said:So if i follow your mind, now the level does not reflect the level of the battery reflecting his voltage but now the capacity.Ok, let's try, i am now at 20% 5675 Wh. So 100% = 5 x 5675 = 28375Wh, which seems correct. It is really strange that before the update, the level reflect exactly the reference of the battery csv. I have always used this to charge at 3.8V per cell my box for storage. I do this for my RC models as for my box .I must simply change my reference observing the charge for my different box, regarding what is the Wh at 3.8vAn update: i am now at 25% 25% with 6955Wh which mean 27820Wh.... this fluctuate a lot And after changing the power in Kanthal using Escribe, so i reloaded the parameter, i get this: A jump to 46% from before 25%...... really strange Link to comment Share on other sites More sharing options...
michaelraynold Posted December 29, 2016 Report Share Posted December 29, 2016 LostVape Triade DNA250I just notice a difference between SP3 and the latest SP5 when i charge it on my laptopSP3 Currently stable at 1.9A chargingSP5 Currently Stable at 0.9A chargingIs this some kind of issues or evolv remove the 2A charging feature on dna 250 at their latest servicepack?Thanks Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now