vegabob Posted December 13, 2015 Author Report Share Posted December 13, 2015 Hello all Nick asked me to get some 510 tools made up to screw in to the 510 on your DNA200 mods. Then in Escribe you run Atomizer Analyzer to get the internal resistance of your mods. Then take the resistance reading and go to the mod tab, enter the reading under mod Resistance and upload settings to device. Now your DNA200 mod will be programmed with its internal resistance. If your interested send me a message on here or Email me at bob.bmb.lewis.03@gmail.com. These tools are in The USA. Link to comment Share on other sites More sharing options...
Nick Posted December 13, 2015 Report Share Posted December 13, 2015 These are great tools for anyone making mods. To get the most out of any device it absolutely should have the internal/mod resistance measured and accounted for. Can't wait to get mine, I've been using non-copper plugs up until now. Link to comment Share on other sites More sharing options...
vegabob Posted December 13, 2015 Author Report Share Posted December 13, 2015 Thanks Nick I hope I did as you asked Link to comment Share on other sites More sharing options...
mactavish Posted December 15, 2015 Report Share Posted December 15, 2015 I ordered two, will make a great surprise Christmas gift for a fellow Vaporshark user! Thanks again for taking an idea for a needed accessory that hopefully someday all mod makers will include with their mods, and GETTING IT MADE! Hats off to you!!! Link to comment Share on other sites More sharing options...
vegabob Posted December 15, 2015 Author Report Share Posted December 15, 2015 Thanks and I just ran with Nicks idea. Link to comment Share on other sites More sharing options...
Tepid Posted December 15, 2015 Report Share Posted December 15, 2015 I agree with mactavish.PM sent. Link to comment Share on other sites More sharing options...
vegabob Posted December 15, 2015 Author Report Share Posted December 15, 2015 Did you get one too Tepid? Link to comment Share on other sites More sharing options...
Michael Hancock Posted December 16, 2015 Report Share Posted December 16, 2015 Huge props to Bob for getting these done. It wasn't a easy project for him to get done but he did. Mine will be here Friday so I'm curious to see how accurate using the 510 adapter filled with solder was/is. Thanks again Bob for the time & work you put in. Mike Link to comment Share on other sites More sharing options...
vegabob Posted December 16, 2015 Author Report Share Posted December 16, 2015 Thanks Mike. Link to comment Share on other sites More sharing options...
Lilpetabread Posted December 16, 2015 Report Share Posted December 16, 2015 PM sent. Thanks Bob. Link to comment Share on other sites More sharing options...
blueridgedog Posted December 16, 2015 Report Share Posted December 16, 2015 Great...sent you a PM. Link to comment Share on other sites More sharing options...
vegabob Posted December 18, 2015 Author Report Share Posted December 18, 2015 PM's have been replied to. You can send me an Email at bob.bmb.lewis.03@gmail.com Link to comment Share on other sites More sharing options...
Michael Hancock Posted December 18, 2015 Report Share Posted December 18, 2015 I got mine today and it is a great tool. Perfect weight, excellent build quilty. Excellent Job! Link to comment Share on other sites More sharing options...
santo19586 Posted December 18, 2015 Report Share Posted December 18, 2015 thanks for doing this bob lewis Link to comment Share on other sites More sharing options...
vegabob Posted December 19, 2015 Author Report Share Posted December 19, 2015 Your all very welcome. BUT I did not do this my self Nick from Evolv came up with the idea. I check out a shop they wanted to much money to make it worth wild, then I talked to Ed Green from Smoke free mods and he found a machine shop to get them done. So it was really a 3 or 4 person show to get these done. I'm just glad they turned out the way they did and every one that has got them says they work great. That's all we can ask for. Link to comment Share on other sites More sharing options...
Michael Hancock Posted December 19, 2015 Report Share Posted December 19, 2015 Props to all involved! This was defiantly needed. Of course this tool opens a new can of worms. Lol I reran the test yesterday and my thermal numbers came out different then all of the other runs I did. Now that I'm 100% sure that I have a proper tool for a "short/complete circuit", or what ever one wants to call it, I have to question all these files that are out there and being used for setting the VT200 settings, including my own. Guess it's time to run the test a couple more times to see if I get consistent numbers and then open yet another thread about this. Lol Link to comment Share on other sites More sharing options...
mactavish Posted December 21, 2015 Report Share Posted December 21, 2015 I was not too happy when I first ran the atomizer analizer. The threading seemed loose, I got various ohm readings, and as I tightened it down, it showed no ohms, and then untightning I got various readings, I could get as low as a .007 ohm reading between the no ohm reading, and the looser adapter screwed in position. I went back and re-read the case resistance thread, and noted: MAKE SURE TO RESET THE MOD RESISTANCE TO ZERO BEFORE RUNNING TEST!!! This of course means connecting the MOD, it downloads your current settings, then reset the mod resistance to ZERO, upload that back to the mod, then use the copper adapter, and run the atomizer analizer. (THIS SHOULD BE A STICKY FOR OTHERS) After doing this, screwing in the copper adapter worked PERFECTLY, screwed all the way till snug, gave me a reading of .005 on my Vaporshark DNA200, which came with an average setting of .007. I set Escribe to 85% (Evolve recommends using 80-90% of your test ohm reading) of my .005 result, to a final resistance setting of ".00425". HAPPY NOW! Hope this helps others! Link to comment Share on other sites More sharing options...
vegabob Posted December 21, 2015 Author Report Share Posted December 21, 2015 Yes you must go the the mod tab first to clear any settings that are there now. Then go to Atty Analyzer to use the tool. Now as far as the 85% thing I am not using that any more, because these tools have the lowest resistance we could find to make them out of I don't feel we need to use the 85% number any more. I'm using the full reading from the tool to put in to my Mods. I think that 85% number was came up with because we were using Atties with wires to do this test before this tool was made. Nick from Evolv came up with the idea for this tool Ed and I just got them made up he can join in and tell us what he thinks about the 85% thing now. Remember everything has resistance ( true ) but with these being made out of 99.9% pure copper and .1% pure silver I think the ohm reading would be so low it really will not matter any more. I do make sure my 510 poss pin is clean will I run my tests. I think using some no loc on the tool would even lowere the reading as well but how much off a difference it would made? I'm not sure. Link to comment Share on other sites More sharing options...
elitegunslinger Posted December 22, 2015 Report Share Posted December 22, 2015 Got mine in the mail; worked great, 0.006 internal on my mod. Link to comment Share on other sites More sharing options...
vegabob Posted December 23, 2015 Author Report Share Posted December 23, 2015 Thanks for letting me know you got them and letting other know how good these work Link to comment Share on other sites More sharing options...
Lilpetabread Posted December 23, 2015 Report Share Posted December 23, 2015 vegabob said:Thanks for letting me know you got them and letting other know how good these work Just got mine, Bob! I shall try it out in a bit!! Thanks again! Link to comment Share on other sites More sharing options...
gratefulbuddy Posted December 24, 2015 Report Share Posted December 24, 2015 Got mine today. Results with the tool match my results with full copper dogev1 and 14ga solid copper romex wire (0.007?) but this tool is MUCH easier to use than that setup. Thanks a bunch vegabob! Link to comment Share on other sites More sharing options...
vegabob Posted December 26, 2015 Author Report Share Posted December 26, 2015 Thanks for letting us know how you like these everyone. Link to comment Share on other sites More sharing options...
phatmitz Posted December 27, 2015 Report Share Posted December 27, 2015 Just got my set in as well. Works great tested on the Reuleaux internal resistance @0.004 Thanks again Bob Link to comment Share on other sites More sharing options...
cloud_nine Posted January 4, 2016 Report Share Posted January 4, 2016 I just received mine last week, and was extremely pleased with the prompt communication and shipment. This tools works perfectly. Thank you for this innovative solution!! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now