vegabob

It's a 900mah battery I forget the name of the wood but it's some hard wood from Africa that they make guatars out of. The work on the mod is why I bought it. And even the box the mod comes in is nice.

I was very lucky to pick up one of these Music City mods my self. The quality workmanship in these mods is awesome. You can tell a craftsmen built these mods

This is a Mod MAMU has made for me it's 41/41/93mm it's got a 1,5000 mah battery in it a Fatdaddy V4 510. She only made 2 of these and I was lucky to get one. I'm so glad MAMU is back in the Modding game a little bit. I have wanted one of her EVOLV product mod for 3.5 years. For people that don't know who MAMU is she is one of the OG Modders from years ago. Her mods are very hard to get your hands on, like I said I was very lucky to get this sweet little mod. I own a lot of high end mods but to me because of what MAMU has done for the Modding world from way back I hold this mod closer to my heart than any thing else I own. I have thanked her over and over for letting me be the one to care for your work of art.

Thanks

If your trying to buy one of these 510 Tools please go to www.smokefreemods.com And you can buy them from the website thanks

Thank you for letting me know how these tools worked out.

Good that's how I use these tools my self

I use the full reading now not the 85.%

I'm glad it all worked out Larry

Your email has been replied to sir

Thanks for letting us know how you like these everyone.

Thanks for letting me know you got them and letting other know how good these work

Yes you must go the the mod tab first to clear any settings that are there now. Then go to Atty Analyzer to use the tool. Now as far as the 85% thing I am not using that any more, because these tools have the lowest resistance we could find to make them out of I don't feel we need to use the 85% number any more. I'm using the full reading from the tool to put in to my Mods. I think that 85% number was came up with because we were using Atties with wires to do this test before this tool was made. Nick from Evolv came up with the idea for this tool Ed and I just got them made up he can join in and tell us what he thinks about the 85% thing now. Remember everything has resistance ( true ) but with these being made out of 99.9% pure copper and .1% pure silver I think the ohm reading would be so low it really will not matter any more. I do make sure my 510 poss pin is clean will I run my tests. I think using some no loc on the tool would even lowere the reading as well but how much off a difference it would made? I'm not sure.

Your all very welcome. BUT I did not do this my self Nick from Evolv came up with the idea. I check out a shop they wanted to much money to make it worth wild, then I talked to Ed Green from Smoke free mods and he found a machine shop to get them done. So it was really a 3 or 4 person show to get these done. I'm just glad they turned out the way they did and every one that has got them says they work great. That's all we can ask for.

PM's have been replied to. You can send me an Email at bob.bmb.lewis.03@gmail.com

Thanks Mike.

Did you get one too Tepid?

Thanks and I just ran with Nicks idea.

Thanks Nick I hope I did as you asked

Hello all Nick asked me to get some 510 tools made up to screw in to the 510 on your DNA200 mods. Then in Escribe you run Atomizer Analyzer to get the internal resistance of your mods. Then take the resistance reading and go to the mod tab, enter the reading under mod Resistance and upload settings to device. Now your DNA200 mod will be programmed with its internal resistance. If your interested send me a message on here or Email me at bob.bmb.lewis.03@gmail.com. These tools are in The USA.

My VT200 board dried after a month of use, not smcgasing not hook up to Escripe I tried forcing the firmware over and over. With no luck my dealer told me I had no warranty witch was BS so I just replaced the DNA200 my self and it's working fine. So I'll RMA the board bad to Evolvv

I have used a small wooden pick in the round hole closet to the end on the ribbon cable to help push the cable in plug.

So true

I should have more info in the next couple of days.