Cehpalomods Posted July 3, 2015 Author Report Posted July 3, 2015 Just finished my temporary box and was curious what other people might have thrown together by now. Post 'em!
ryanschram Posted July 3, 2015 Report Posted July 3, 2015 I would've had mine together, but my chip is DOA. Working with the vendor to get that situation un-fuggered up...
alee132 Posted July 3, 2015 Report Posted July 3, 2015 Thats epic, those buttons look like gamecube controller buttons lol.
alee132 Posted July 3, 2015 Report Posted July 3, 2015 ryanschram said:I would've had mine together, but my chip is DOA. Working with the vendor to get that situation un-fuggered up...Thats not a good sign. I had heard 1 other guy had a good board but the screen was bad. He installed it and was able to use mod without screen till protovapor sent him a new chip/screen.
Cehpalomods Posted July 3, 2015 Author Report Posted July 3, 2015 alee132 said:Thats epic, those buttons look like gamecube controller buttons lol. N64 to be exact. I'm actually building my final device into an N64 controller!
ryanschram Posted July 3, 2015 Report Posted July 3, 2015 well, they're sending me a new chip/screen with a return label for the old one. Great service from protovapor.
Crushkrew Posted July 3, 2015 Report Posted July 3, 2015 alee132 said:[QUOTE=ryanschram]I would've had mine together, but my chip is DOA. Working with the vendor to get that situation un-fuggered up...Thats not a good sign. I had heard 1 other guy had a good board but the screen was bad. He installed it and was able to use mod without screen till protovapor sent him a new chip/screen.[/QUOTE]
Crushkrew Posted July 3, 2015 Report Posted July 3, 2015 I'm the guy with the dead screen.....protovapor has great customer service... Went the same temp route with the clear hammond....here's a vid of messing with software... https://m.youtube.com/watch?v=LZF3Vi1nndI
Crushkrew Posted July 3, 2015 Report Posted July 3, 2015 Cehpalomods said:Just finished my temporary box and was curious what other people might have thrown together by now. Post 'em! What size lipo do you have jammed in there?
Crushkrew Posted July 3, 2015 Report Posted July 3, 2015 Got one of my rc plane batts more fit...more mah....
lolerwaffles Posted July 4, 2015 Report Posted July 4, 2015 18650x3, with balance leads properly installed. 2500mah
TheFogginSailor Posted July 5, 2015 Report Posted July 5, 2015 lolerwaffles, cool to see more 3d printers out here.is it possible to get a peek inside? hand how did you get the battery meter to work?
RickAdair Posted July 5, 2015 Report Posted July 5, 2015 Here is my first prototype. Still waiting on my lipo.
adski Posted July 6, 2015 Report Posted July 6, 2015 Printed this one I found on the web.The buttons needed sanding down a bit but apart from that perfect fit.1400mah lipo, FDV low profile 510.Broke my ribbon cable as i have sausage fingers but it worked perfectly before that.Thanks to whoever designed it.I did have it in an ipv3 case with the button holes filled with chemical metal then re-drilled but my bayttery was too big.http://imgur.com/uQBQI3Shttp://imgur.com/zyoKuKL
SG MoDz Posted July 6, 2015 Report Posted July 6, 2015 Have had mine up running for a bit over a week really liking it so far!
Crushkrew Posted July 8, 2015 Report Posted July 8, 2015 Very nice...is that a 1590g? And can you post a pic of inside? Thx...J
mandro Posted July 8, 2015 Report Posted July 8, 2015 There are some nice looking DIY mods being posted. I hope to finish mine this weekend and I'll post a photo.
kaotikgood Posted July 9, 2015 Report Posted July 9, 2015 MADMODDER said:Here is my prototype Amazing work! Do you mind measuring the minimum and maximum depth into the box that the 200 creates inside your box as well as the boxes wall thickness? Much appreciated if you are willing.
alee132 Posted July 10, 2015 Report Posted July 10, 2015 adski said:Try that again..http://imgur.com/09QXypiI saw that on shapeways and thingiverse. That blueridge guy made it. What size lipo goes in it?
alee132 Posted July 10, 2015 Report Posted July 10, 2015 Wibberly said: My contraptionWow dude now that is original and cool looking. What is that material? It looks like you made the enclosure by hand. Kinda has a steampunk look to it going on. Nice. Looks kinda wide though. Does it fit good in the hand? Could just look like its wide because no reference points.
Phone Guy Posted July 11, 2015 Report Posted July 11, 2015 Awesome looking boxes... anybody have a good source for a pre-milled metal enclosure with the buttons?
blueridgedog Posted July 11, 2015 Report Posted July 11, 2015 adski said:Try that again..http://imgur.com/09QXypiThis is a test enclosure I posted. I have since lowered the window to make management of the ribbon easier, but you still have to sand the buttons due to variations in printing...they need to fit tight so there is no deflection.Can you tell me how the snap enclosure on the back worked?
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now