mactavish Posted November 15, 2016 Report Share Posted November 15, 2016 Spirometry said:SP3 added some extra protections. Reading the ultra low resistances with the copper plug will just display a question mark. Thanks! That's odd though since when I wrote my posts earlier in this thread, I believe I was using SP3. I did see the "?", but after making the plug really tight, it showed the resistance. I could be mistaken on the SP version I was using at the time. I do hope they fix the issue. Link to comment Share on other sites More sharing options...
mactavish Posted November 16, 2016 Report Share Posted November 16, 2016 Wayneo said:Has anyone managed to retest with this latest SP5 to see if this is working again? I know mine is somwhere around here, I'll just have to hunt it down. I just ran SP5, on my new VS Switchbox DBA75, which came from VS with a ".004" already set. Zeroed settings, use the copper plug, and got the EXACT same number. So I would say it worked! Link to comment Share on other sites More sharing options...
retird Posted November 16, 2016 Report Share Posted November 16, 2016 6-5-2016 is the latest firmware version for the DNA75. Check the lower right hand corner of Device Monitor and the Switchbox should show that version.Vapor Shark did an excellent job programming the Switchbox with the production utility. Link to comment Share on other sites More sharing options...
Wayneo Posted November 16, 2016 Report Share Posted November 16, 2016 mactavish said: ... new VS Switchbox DBA75, which came from VS with a ".004" already set. Very sharp looking mod. Thanks for trying.When I ran it with the Feb software, I fely very uncomfortable with how much I tightened it down, especially on my Reuleaux, knowing the quality of that 510. Link to comment Share on other sites More sharing options...
mactavish Posted November 16, 2016 Report Share Posted November 16, 2016 Wayneo said: Very sharp looking mod. Thanks for trying.When I ran it with the Feb software, I fely very uncomfortable with how much I tightened it down, especially on my Reuleaux, knowing the quality of that 510. You are welcome. With SP5 I did NOT have over tighten, but I did not test that aspect on any of my other DNA devices. Link to comment Share on other sites More sharing options...
Wayneo Posted January 24, 2017 Report Share Posted January 24, 2017 Has anyone managed to retest with this latest EScribe 1.2 SP5.2 to see if this is working again? Or even better, is it on any official list for it to be fixed in the future, which should then show up in the notes for each new release. Link to comment Share on other sites More sharing options...
dwcraig1 Posted January 25, 2017 Report Share Posted January 25, 2017 Best I can tell, just checked a few of mine, is that it still doesn't function properly. EScribe 1.2 SP5.2 on my computer has firmware for 200/250 dated 12-22-2016. Still shows "?" Link to comment Share on other sites More sharing options...
Wayneo Posted January 25, 2017 Report Share Posted January 25, 2017 I'm just waiting on a few last parts before getting myself a new mod built and I'll need to run my own MFG settings. Luckily I have an old version 2016/02/23 which works. Link to comment Share on other sites More sharing options...
Zaptear Posted October 17, 2017 Report Share Posted October 17, 2017 Can’t u just short out ur rda with copper wire to do the same thing ? Link to comment Share on other sites More sharing options...
giz_60 Posted October 17, 2017 Report Share Posted October 17, 2017 56 minutes ago, Zaptear said: Can’t u just short out ur rda with copper wire to do the same thing ? You can, but there is a slight amount of resistance in the wire as well.... Link to comment Share on other sites More sharing options...
Zaptear Posted October 17, 2017 Report Share Posted October 17, 2017 How does one buy this tool then any links Link to comment Share on other sites More sharing options...
giz_60 Posted October 17, 2017 Report Share Posted October 17, 2017 http://smokefreemods.webs.com/apps/webstore/ Link to comment Share on other sites More sharing options...
Zaptear Posted October 17, 2017 Report Share Posted October 17, 2017 Thanks this is my dna 250 from Modz by nasy trying to find a discharge profile for a max amps 1850 mah 3s Link to comment Share on other sites More sharing options...
Zaptear Posted November 23, 2017 Report Share Posted November 23, 2017 On 10/17/2017 at 8:55 AM, giz_60 said: http://smokefreemods.webs.com/apps/webstore/ Link not working Link to comment Share on other sites More sharing options...
mactavish Posted November 23, 2017 Report Share Posted November 23, 2017 7 minutes ago, Zaptear said: Link not working Just clicked it on an iPad opened fine in Safari. Check your internet settings. Link to comment Share on other sites More sharing options...
Zaptear Posted November 23, 2017 Report Share Posted November 23, 2017 8 minutes ago, mactavish said: Just clicked it on an iPad opened fine in Safari. Check your internet settings. Link to comment Share on other sites More sharing options...
mactavish Posted November 23, 2017 Report Share Posted November 23, 2017 Are you in the USA? I just clicked it again, here is the screenshot. Link to comment Share on other sites More sharing options...
Wayneo Posted November 23, 2017 Report Share Posted November 23, 2017 Yo @mactavish, the url you show (that works), is not the same as his on his mobile. His 'fix' I'd betcha is written on his image posted. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now