txmonkey214 Posted August 30, 2016 Report Share Posted August 30, 2016 Are your battery cells charging at the same level? Low/bad batteries will cause erratic behavior in any device. If not, send it back. Link to comment Share on other sites More sharing options...
Karsten Posted August 30, 2016 Author Report Share Posted August 30, 2016 txmonkey214 said:Are your battery cells charging at the same level? Low/bad batteries will cause erratic behavior in any device. If not, send it back.Battery charges perfectly. Cells are all even. Link to comment Share on other sites More sharing options...
Karsten Posted September 2, 2016 Author Report Share Posted September 2, 2016 Sent it back in for repair. Hoping they'll try loading my .ecig and seeing if that kills the display before sending it back again!If anyone else is willing to risk losing their display, it would be interesting to see if it is, in fact, the .ecig file - I'm attaching it here...volcano-900mah-lavabox-preset-files.ecig Link to comment Share on other sites More sharing options...
retird Posted September 2, 2016 Report Share Posted September 2, 2016 If you suspect your .ecig file it might be better to create a new one when you get your repaired device back. I personally don't download/upload any unknown/suspect .ecig file. Link to comment Share on other sites More sharing options...
Karsten Posted September 3, 2016 Author Report Share Posted September 3, 2016 That's the plan - but if it's a particular configuration of settings it won't matter... Link to comment Share on other sites More sharing options...
VapingBad Posted September 3, 2016 Report Share Posted September 3, 2016 I can't see anything in the config that would explain your issue, I copied the screen settings to a DNA 200 and they work fine, I would decrease the fade in time to 0.25 myself. Link to comment Share on other sites More sharing options...
BillW50 Posted September 3, 2016 Report Share Posted September 3, 2016 retird said:If you suspect your .ecig file it might be better to create a new one when you get your repaired device back. I personally don't download/upload any unknown/suspect .ecig file. I have, but only to EScribe and haven't uploaded any to a mod. Link to comment Share on other sites More sharing options...
Karsten Posted September 3, 2016 Author Report Share Posted September 3, 2016 VapingBad said:I can't see anything in the config that would explain your issue, I copied the screen settings to a DNA 200 and they work fine, I would decrease the fade in time to 0.25 myself. I actually had them at .25 & .75 but changed to 1 & 1 as part of the testing Link to comment Share on other sites More sharing options...
retird Posted September 11, 2016 Report Share Posted September 11, 2016 @Karsten so, I guess you got your device back that you sent about 9 days ago to Evolv by now.... How's it working? Still loosing the display??? Link to comment Share on other sites More sharing options...
Karsten Posted September 11, 2016 Author Report Share Posted September 11, 2016 retird said:@Karsten so, I guess you got your device back that you sent about 9 days ago to Evolv by now.... How's it working? Still loosing the display??? I got it back yesterday but am waiting until Monday morning to fire it after I recreate an ecig Link to comment Share on other sites More sharing options...
retird Posted September 11, 2016 Report Share Posted September 11, 2016 Are you going to fire it and check it out before changing the ecig file? Let us know how it goes... I would probably maker sure I had a properly functioning device before making any changes, but that's just me... Link to comment Share on other sites More sharing options...
Karsten Posted September 11, 2016 Author Report Share Posted September 11, 2016 retird said:Are you going to fire it and check it out before changing the ecig file? Let us know how it goes... I would probably maker sure I had a properly functioning device before making any changes, but that's just me... I did switch it to a default Ti profile and gave it about 3 or 4 quick presses. The screen stayed on but that's enough to confirm what I needed before creating a new ecig. I want to test it connected to the PC as well. Plus, I don't know what curve is in there for Ti and would rather not fry a good coil Link to comment Share on other sites More sharing options...
retird Posted September 11, 2016 Report Share Posted September 11, 2016 Understand wanting to not fry a new coil... when I start using or testing a new coil, material, or new coil technology I usually start with a low temp and wattage and migrate upwards... Ti was too "touchy" for me so I don't use it... Link to comment Share on other sites More sharing options...
Karsten Posted September 11, 2016 Author Report Share Posted September 11, 2016 retird said:Understand wanting to not fry a new coil...Ti was too "touchy" for me so I don't use it... It's a Ti Clapton. Best flavor of any material so far. Works great with right curve. Current plan is to bring it up on a basic kanthal and run it for a bit before loading up my Ni200, SS, and Ti's for TC. Debating on whether or not to just blast a full config at it, including screens first go around and basically say 'screw it' and fire up, or take it one step at a time until something either causes it to behave as before or I end up with a good ecig and functional DNA at same time... Link to comment Share on other sites More sharing options...
retird Posted September 11, 2016 Report Share Posted September 11, 2016 Yep one could implement an ecig file is steps or all it once. If you suspected the ecig file as subject to have caused your issue then it's your call whether to implement all at once or not. I think I would first save the ecig file currently in the device so it might be reloaded should it be needed. Good luck and let us know. Link to comment Share on other sites More sharing options...
Karsten Posted September 17, 2016 Author Report Share Posted September 17, 2016 Happy to report that after going through both the one-step and all-at-once the DNA200 is performing flawlessly. So, it was either two bad boards in a row or one bad board that was just restored and sent back. Either way the guys at Evolv were great. While it would've been nice to have known what the issue was, it's not a requirement and I'm still a happy user. Link to comment Share on other sites More sharing options...
retird Posted September 17, 2016 Report Share Posted September 17, 2016 Karsten said:Happy to report that after going through both the one-step and all-at-once the DNA200 is performing flawlessly. So, it was either two bad boards in a row or one bad board that was just restored and sent back. Either way the guys at Evolv were great. While it would've been nice to have known what the issue was, it's not a requirement and I'm still a happy user. THX for the update..... enjoy Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now