Wayneo

You'd need to open a Help Desk ticket for that. The 60C screens are delicate, especially that 'fusible link' near the board end. I've been openly saying this since 2024 to one of your guys here https://forum.evolvapor.com/topic/72310-dna60c-screens/#comment-941274

I don't believe you can change it either way, any longer. Also 4.35V is fully charged not overcharged.

Do you actually use Replay? enabled after seeing the ready? During testing I vaped a N80 coil and wick perfectly dry with no burn. 30+ puffs from when the rda was dry. I got nic sick thinking it would be much fewer puffs. It never burned/singed the cotton.

Sure. Replay works best with a proper TC material like SS. You are quite lucky to get a 'replay ready' with N70. You must use enough watts or long puff for the mod to be able to capture the puff. I will assume the 4th that does not show 'replay ready' is your kanthal coil with the flattest/lowest change in resistance.

Or did you charge via your PC? Was there a pod in your mod when you created the screenshot? There is newer firmware, can you update to that and do one last screenshot (low chance, and you should contact OXVA for repair or replacement) Thank you for that screenshot.

The charger you used, what does it say on the label for voltage and current? With your mod plugged in, Start escribe -> Device Monitor and then do a full screenshot. Post the image here.

That link was nearly 10 years old and not for color mods, but you see many parts are still relevant. I think djlsbvapes - and jai Haze made videos about escribe and features except session mode which is newer.

OK, so you see from the 'save' it's what you want to do, and the 'cancel' is when you want to stop. At that point (after you clicked save) if you clicked 'connect and download' you'd see 'Puff Saved, Playing' has been enabled by YOUR MOD. Replay ONLY captures what your last puff tasted/heated. Nothing to do with duration at all. For wattage and duration you want 'session mode' Yup. At most you can uncheck that, otherwise there is no 'puff' for it to recreate. For the third time 'Your mod toggles that 'playing' on and off. Not a faulty chip, there are YT videos on how to use. What training video did you find? There never was one (by evolv) for any color mod. On YT all 75C/100C/250C's operate the same. Or search here for more info on session mode.

What problem(s) are you actually having? NO YOU DO NOT Go read my last sentence again

Exactly what it says. That field ONLY ever shows when the field above it 'enable replay' is checked/enabled above it, and YOU have enabled Replay for that profile. Your mod toggles that 'playing' on and off.

Under the 'safety' tab in escribe, you can adjust that 'fill pod' sensitivity or even turn it off. BUT IT IS WORKING (high watts, low airflow) as you've found out, caused by the wicking not able to keep up.

OK, so you got A bad pod.

No, and no.

I would say the evolv default theme fits that bill.

I don't know, but you can find the chip specs and dimensions on Stealthvape in the UK. I would measure the distance from the bottom actuator to the USB connector. Good luck.

Open a ‘Help Desk’ ticket with your request/suggestion https://bit.ly/4616VB3

In a color theme you can change the fonts used to ones on your PC. Try that.

Post moved to proper area. What I typed still stands. Thank you.

If this is what your mod looks like, remove the panel over the fire button and see if the problem still exists. Is that a color screen on the mod? You can also (with mod plugged in) use escribe - Device Monitor and the bottom line will show what buttons are being pressed. Sounds like a stuck 'down' button, but is it from the board or panel.

Open a ‘Help Desk’ ticket with your suggestion Click Here

Open a ‘Help Desk’ ticket ⬇️ Link in my signature line. ⬇️ Report back with their answers

You can lower or turn off 'fill pod' in escribe - safety tab. Load the latest firmware first.

If that feature works on the 60C you can try the serial command u=0 A to disable charging.

I have no clue about the OXVA quality control. What I can say is I consistently get more than double your 2,000 puffs on the 0.6 pods, and my wife gets more than double what I get on the 0.8 pods. No sweetener DIY ejuice.

Read the post below and try the firmware if you want. https://forum.evolvapor.com/topic/76162-possible-bug-or-board-problem-and-firmware/