Wolf_7 Posted August 14, 2016 Author Report Share Posted August 14, 2016 Hey everyone, I have a lava box dna 200 bone white, with a kanger top tank mini. It recently came in the mail( like yesterday) and almost 80% of the time it says check atomizer. Any feedback will be helpful thank you Link to comment Share on other sites More sharing options...
dwcraig1 Posted August 14, 2016 Report Share Posted August 14, 2016 I'm going to have to guess at it but I suspect Kanger is still using that sliding 510 pin in the base of the atomizer as with the ST mini. Probably the pin is not getting pressed in good to make connection with the heads positive pin. Try pressing it in before screwing on the atty and see if that seems to help. Link to comment Share on other sites More sharing options...
Spector NS5 RD Posted August 14, 2016 Report Share Posted August 14, 2016 welcome to the forum wolf_7. most likely something with your top tank or the tank itself is not making a good connection to the mod. try another tank. if the problem goes away, it's the top tank that's the problem. if the problem persists, there could be something wrong with mod's 510. possibly a stuck positive pin.make sure the coil is screwed in tight, and the tank tight to mod.you can also open atty analyzer in escribe and check your atty's stability. try slightly unscrewing the tank on and off a little while watching the ohms. also rock the tank back and forth while it's screwed tightly on the mod and see what the ohms do. Link to comment Share on other sites More sharing options...
Wolf_7 Posted August 14, 2016 Author Report Share Posted August 14, 2016 ChunkyButt200 said:welcome to the forum wolf_7. most likely something with your top tank or the tank itself is not making a good connection to the mod. try another tank. if the problem goes away, it's the top tank that's the problem. if the problem persists, there could be something wrong with mod's 510. possibly a stuck positive pin.make sure the coil is screwed in tight, and the tank tight to mod.you can also open atty analyzer in escribe and check your atty's stability. try slightly unscrewing the tank on and off a little while watching the ohms. also rock the tank back and forth while it's screwed tightly on the mod and see what the ohms do. okay I will try watching them in escribe, what should I look for with the ohms exactly. A lot of variation or super consistency Link to comment Share on other sites More sharing options...
Spector NS5 RD Posted August 14, 2016 Report Share Posted August 14, 2016 Wolf_7 said: okay I will try watching them in escribe, what should I look for with the ohms exactly. A lot of variation or super consistency one thing to do even without using atty analyzer is see if your coil is reading correctly on your lava box. if they're rated on the package as 0.25 (just an example) and your mod is reading it as .30 or above then you have a poor connection somewhere, whether it be the coil, where the coil screws in to the base or where the base screws into the 510 or even the 510 itself. what to look for in AA is basically the same thing, high ohms and/or if you see the "?" instead of a reading. "check atomizer" means the mod is losing connection to the atty, a complete disconnect. also, make sure the spring loaded 510 pin is......still "springy" and moves freely up and down. i have heard of one person here crushing their 510 connector pin permanently down on their lavabox from screwing down an atty that had a very long 510. Link to comment Share on other sites More sharing options...
Wolf_7 Posted August 14, 2016 Author Report Share Posted August 14, 2016 ChunkyButt200 said:one thing to do even without using atty analyzer is see if your coil is reading correctly on your lava box. if they're rated on the package as 0.25 (just an example) and your mod is reading it as .30 or above then you have a poor connection somewhere, whether it be the coil, where the coil screws in to the base or where the base screws into the 510 or even the 510 itself. what to look for in AA is basically the same thing, high ohms and/or if you see the "?" instead of a reading. "check atomizer" means the mod is losing connection to the atty, a complete disconnect. also, make sure the spring loaded 510 pin is......still "springy" and moves freely up and down. i have heard of one person here crushing their 510 connector pin permanently down on their lavabox from screwing down an atty that had a very long 510. it's a .5 reading at .7 so Im assuming it's not tight enough. Link to comment Share on other sites More sharing options...
VapingBad Posted August 14, 2016 Report Share Posted August 14, 2016 It could be whatever holds the spring at the bottom of the 510 is loose and not applying enough pressure or a poor ground connection to the 510. Link to comment Share on other sites More sharing options...
Wolf_7 Posted August 16, 2016 Author Report Share Posted August 16, 2016 VapingBad said:It could be whatever holds the spring at the bottom of the 510 is loose and not applying enough pressure or a poor ground connection to the 510. anyway to fix it would I have to send it back Link to comment Share on other sites More sharing options...
Doyle4 Posted August 16, 2016 Report Share Posted August 16, 2016 Your mod will be fine, im going to jump the gun and confirm its your tank, I help out now and again at a vape shop and the amount of times i have heard and seen this is stupid, it has also happened to my wife.The cause is the pin on the tank, its cheap metal and eventually it compresses, what you have also spotted is what i was about to comment, your ohms will read oddly, this is due to the pin been compressed and making a slight connection to the negative giving a false reading, soon it will just die and not pickup on any mod. My suggestion is get your self a semi decent tank, Aspire Cleito is a cheapish good tank. Now you have a DNA, dont put Kanger junk on it, make the most of your DNA experience. Link to comment Share on other sites More sharing options...
VapingBad Posted August 16, 2016 Report Share Posted August 16, 2016 Wolf_7 said: anyway to fix it would I have to send it backI don't know, not got a Lava Box, but I mossed that is was a Subtank and the coils heads don't have the best connection on those I have had reasonable results with the RBA deck. Link to comment Share on other sites More sharing options...
BillW50 Posted August 16, 2016 Report Share Posted August 16, 2016 I have eight Subtanks myself and use six of them regularly. I had zero problems with connections with the RBA when I make sure the RBA pin is tight and the wire terminals are tight. I did see a snapshot of somebodies Subtank 510 pin had the plating flaking off and they had connection problems. But none of mine had done that. Link to comment Share on other sites More sharing options...
Dampmaskin Posted August 16, 2016 Report Share Posted August 16, 2016 Remember the first version of the Aerotank, the one that looked like this? If you screwed it too tightly on a 510, the center pin would short out inside the base of the tank. I learned that using a mech mod. Fun times. Link to comment Share on other sites More sharing options...
BillW50 Posted August 16, 2016 Report Share Posted August 16, 2016 Yeah I am not very found of the 510 first used by Joyetech which the rest of the vaping world seems to have adopted. I think the connection is way too small, the threads are too fine, and the space between the center pin to the outside ground is too small. And pushing 200 to 250 watts (and probably far more in the future) through the 510 is just ridiculous. So I am not surprised about all of the common problems that pops up with our 510 connections. Sorry to say, but we need something better. Link to comment Share on other sites More sharing options...
coco Posted September 2, 2016 Report Share Posted September 2, 2016 I think im had same probs too and i cant see my pin 510 work properly and these led tell me atomizer check and before i rebboot led show up ohm too high, AA cant detect ohm meter,help how to fix it Link to comment Share on other sites More sharing options...
BillW50 Posted September 3, 2016 Report Share Posted September 3, 2016 coco said:I think im had same probs too and i cant see my pin 510 work properly and these led tell me atomizer check and before i rebboot led show up ohm too high, AA cant detect ohm meter,help how to fix itThat means it isn't seeing the atomizer. For most of us that means trying another atomizer. Or is this your only one? Link to comment Share on other sites More sharing options...
coco Posted October 15, 2016 Report Share Posted October 15, 2016 I had tried for another atomizer and still cant read ohm, maybe any advice? Link to comment Share on other sites More sharing options...
VapingBad Posted October 15, 2016 Report Share Posted October 15, 2016 Check the 510 centre pin in not stuck or come loose inside. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now