dwcraig1
-
Posts
2,324 -
Joined
-
Last visited
-
Days Won
147
Content Type
Profiles
Forums
Downloads
Posts posted by dwcraig1
-
-
i have mistakenly been giving you advice for a non color board, my apologies.
Wayne sent me this just now.
-
this gets me this.
With temperature dominant the large number will be temperature instead of watts.
-
Do you have this box checked/unchecked? If so uncheck or check it depending with what you want and upload settings.
-
Look here for resample coil resistance.
-
Make your desired adjustments here and upload settings.
-
It appears that you have reset the board to default values which would set it for 3 cells.
Connect to eScribe and go to Mod/Battery and change from 3 cell to 2 cell and upload settings.
-
I buy from here. You can refine your search on the left side of the page pretty well.
https://hobbyking.com/en_us/batteries-chargers/batteries/lipo.html
-
1
-
-
You need a new battery. The voltage is way to low to safely charge it.
-
2
-
-
On 11/26/2020 at 4:34 AM, eStress said:
Odin mini.ecig 35.5 kB · 91 downloads
Appears to be for 250 Color
-
1
-
-
This is something that I have never done till now.
On the the top of forum page I choose create then file download then Theme Park. Select which DNA group.
I had saved the theme to desktop using EScribe.
The images are there once your post is opened.
-
I did see the "B" but at the time didn't realize it was "Board"
I think you have found the problem......or a problem.
Earlier screen shots doesn't show it that hot.
-
If preheat (1 watt) is set lower than power (33 watts) it has no effect.
-
1
-
-
If your mod's resistance is 0.004 ohm and you set it to 0.002 or 0.005 it will make almost no difference to your problem.
-
Are you setting your cold resistance again after the coil is heated? If so it will use that setting as the cold resistance and be hotter than what it reports.
-
-
Try to keep it 220 C degrees or lower.
If you want to use spaced coils try making the wraps closer together.
I use contact coils only but many prefer spaced, your choice. Try to keep the whole coil in the air flow.
-
Are the first couple of hits good?
-
Are you cutting your wick to this length?
-
It looks to me that the mod maybe is jumping out of TC and into wattage mode. Device Monitor in EScribe will help determine that.
Perhaps poor connections between board and coil resulting in artificial resistance readings.
-
1
-
-
Image of DNA250 non-color firing dry wick with 316L clapton coil with .5 second 60 watt boost then 40 watts.
Same was done with DNA250 Color and results were similar.
I had to hold firing button for several seconds before wick would show signs of burning, 15 seconds fire time.
Voltage output dropped to 1 - 2 volts on both.
-
1
-
-
You should ask here:
-
1
-
-
From what I see you must have a dual battery DNA75C.
If what the arrow in the image is pointing too is what you are asking about and are concerned with where the wire from it goes, it goes to battery negative on the board.
If not your question please post a photo of the part.
-
1
-
-
Here is a snip of my 250C at 91% (left side) and 94% (right side), looks pretty similar to your Centaurus
-
If you have connected it previously to EScribe when the desired theme was present then you most likely have a back up .ecig file for it. Under the Help/Backups.
Dynamic Temperature Display for Vicious Ant?
in General Discussion
Posted
Honestly I don't know, I've been looking for that setting on my VA Spade in Theme Designer and can't find it.
Perhaps Wayneo knows and will answer,