dwcraig1
-
Posts
2,457 -
Joined
-
Last visited
-
Days Won
171
Content Type
Profiles
Forums
Downloads
Posts posted by dwcraig1
-
-
@RealMcCoy Could you post a snippet firing your coil in wattage mode with battery voltage also checked?
In this snippet I have unchecked the "set temperature" box to avoid any confusion. This is wattage with a little boost without using Replay.
-
1
-
-
The coil used in my post is two strands of 28 gauge SS 430 twisted tightly with a drill and in a Kayfun Lite Plus.
-
1
-
-
It appears to me that you are trying to get your perfect puff in TC mode, it doesn't look like your getting a satisfactory puff to base Replay on.
Try this, set your profile to "Watts" then set your wattage and Boost and upload settings, Keep making adjustments till you get that puff that you feel is right.
Use my profile snip as your guide.
Then save puff.
On my snip the test puff is on the left. look at the live ohms to note duration as it's hard to see as it is flat 20 watts.
Use Watt profile. use TC capable wire.
-
Honestly I don't know, I've been looking for that setting on my VA Spade in Theme Designer and can't find it.
Perhaps Wayneo knows and will answer,
-
i have mistakenly been giving you advice for a non color board, my apologies.
Wayne sent me this just now.
-
this gets me this.
With temperature dominant the large number will be temperature instead of watts.
-
Do you have this box checked/unchecked? If so uncheck or check it depending with what you want and upload settings.
-
Look here for resample coil resistance.
-
Make your desired adjustments here and upload settings.
-
It appears that you have reset the board to default values which would set it for 3 cells.
Connect to eScribe and go to Mod/Battery and change from 3 cell to 2 cell and upload settings.
-
I buy from here. You can refine your search on the left side of the page pretty well.
https://hobbyking.com/en_us/batteries-chargers/batteries/lipo.html
-
1
-
-
You need a new battery. The voltage is way to low to safely charge it.
-
2
-
-
On 11/26/2020 at 4:34 AM, eStress said:
Odin mini.ecig 35.5 kB · 91 downloads
Appears to be for 250 Color
-
1
-
-
This is something that I have never done till now.
On the the top of forum page I choose create then file download then Theme Park. Select which DNA group.
I had saved the theme to desktop using EScribe.
The images are there once your post is opened.
-
I did see the "B" but at the time didn't realize it was "Board"
I think you have found the problem......or a problem.
Earlier screen shots doesn't show it that hot.
-
If preheat (1 watt) is set lower than power (33 watts) it has no effect.
-
1
-
-
If your mod's resistance is 0.004 ohm and you set it to 0.002 or 0.005 it will make almost no difference to your problem.
-
Are you setting your cold resistance again after the coil is heated? If so it will use that setting as the cold resistance and be hotter than what it reports.
-
-
Try to keep it 220 C degrees or lower.
If you want to use spaced coils try making the wraps closer together.
I use contact coils only but many prefer spaced, your choice. Try to keep the whole coil in the air flow.
-
Are the first couple of hits good?
-
Are you cutting your wick to this length?
-
It looks to me that the mod maybe is jumping out of TC and into wattage mode. Device Monitor in EScribe will help determine that.
Perhaps poor connections between board and coil resulting in artificial resistance readings.
-
1
-
-
Image of DNA250 non-color firing dry wick with 316L clapton coil with .5 second 60 watt boost then 40 watts.
Same was done with DNA250 Color and results were similar.
I had to hold firing button for several seconds before wick would show signs of burning, 15 seconds fire time.
Voltage output dropped to 1 - 2 volts on both.
-
1
-
Odin Mini 75C
in EScribe, Software and Firmware
Posted
Not actually twisting it makes it stiffer. When I'm done twisting it I heat the length of it to a slight red. I torch all my wire prior to coiling (even Tii).
You could use a Bic lighter if necessary but be sure to dry fire with low wattage to burn off the black stuff.
Twisted lightly really doesn't describe it, it's twisted pretty tight. This makes the 2 strands equal / near 26 gauge with lots of area for juice contact.
This photo is from a couple of years ago, I twist it a bit tighter nowadays.