dwcraig1
-
Posts
2,324 -
Joined
-
Last visited
-
Days Won
147
Content Type
Profiles
Forums
Downloads
Posts posted by dwcraig1
-
-
There is probably a firmware update for you in Escribe. It with tell you when you connect if there's a newer one available
Windows only for this version
.https://downloads.evolvapor.com/SetupEScribe2_SP25_INT_ServicePack.exe
Or for SP24 here: : https://www.evolvapor.com/escribe availible for Windows, Mac and linux
-
2
-
-
-
Are you saying that both mods work now?
-
For what ever reason the battery power isn't making it to the board.
-
Does the board and screen turn on with power power applied vis USB?
-
Well are the batteries installed with correct polarity? And does the battery door's little spring loaded pin appear to connect to the brass plate on the battery door.
I would suggest connecting to Escribe and use Device monitor to see what is says for the voltage of each cell. Check if it reports one cell is above 4.2 volt and the other is real low,
-
Is that three different mods of the same model?
-
My DNA100C has an 18650 Samsung 20S (30 amp) at 90% charge here. I don't have any Kanthal or Nichrome heavy enough to get really low resistance so I used some dual core SS 316 Claptons in dual coil configuration.
Both firings was with the screen timed out (off)
-
1
-
-
6 hours ago, Joshua12345 said:
update: i put the default 100c theme on and it made no difference. it is still doing the wattage drop issue. i honestly think there is something wrong with a connection inside the mod itself
Did you change only the theme or did you use my ecig file?
-
2
-
-
2 hours ago, Joshua12345 said:
update: i put the default 100c theme on and it made no difference. it is still doing the wattage drop issue. i honestly think there is something wrong with a connection inside the mod itself
I don't think it a bad connection as far as wiring, more like the board it's self. This is just my opinion as I am not an Evolv tech.
My advice would be to contact Evolv's Help Desk and they will advise you as to how best to proceed.
https://helpdesk.evolvapor.com/index.php?a=add&category=1
Add a link to this thread on your contact request.
-
1
-
1
-
-
3 hours ago, Joshua12345 said:
Okay so I’m this picture, I have a fully charged Samsung 40 t. The device is set on 80 watts. During a regular hit, it is hitting at 4.17 volts. Once the screen went black, it appears to be hitting at 46 watts, it also appears the volts went down. But after this, if I keep hitting it.. it still says upper 4 volts
The voltage drop looks to be not the problem. If it was a faulty cell or poor connections between the cell and board it would show in this picture.
-
2
-
-
3 hours ago, Joshua12345 said:
Yeah, I’m at work all day. I restored it again, and don’t hit over seventy watts, and the problem doesn’t occur. It’s only if I’m running high wTtage, as well as weak battery on a full charged batt
With a fully charged battery do this again and hoover your mouse over the area of the lowest voltage drop and post it's value, do this with your Samsung 40T.
You should not be getting low battery message firing at 70 watts with a full charged 40T unless your voltage drops below Soft Cell Cutoff and that would be 2.75 volts in most cases.
-
1
-
-
Here is the .ecig file that shipped on my DNA100C
Give it a try if you wish, you can always revert it back easily.
File/open/choose file/upload to device.
-
2
-
1
-
-
So what theme are you currently using?
-
1
-
-
No but I was running your .ecig file and could not reproduce the problem.
-
1
-
-
13 minutes ago, Michael Guercio said:
Mine just did it with stealth mode on & a samsung 30T true 35amp batt..
What was the standing voltage of the cell prior to firing?
-
1
-
-
This is in reference to the coil in the video (0.16 ohms)
It will take a good high amperage cell with good battery sled contacts to achieve 100 watts with that coil.
I left out the one were it calculated to 4 volts but that's what it came out to.
https://www.the12volt.com/ohm/ohms-law-calculators.asp
-
2
-
-
If you can provide us with a snippet like this we very well may be able to see what's going on.
Perhaps tomorrow I'll set up a much lower resistance coil and see if I can reproduce it.
-
1
-
-
This is the version that I am using:
https://downloads.evolvapor.com/SetupEScribe2_SP25_INT_ServicePack.exe
-
1
-
-
Here I have EScribe's Device Monitor open and a DNA60 connected. I have taken a puff and hit the pause button. Then by hoovering the mouse curser over areas on the graph it will show the values at any given point.
Note my cell was at about 4.1 volts before I fired it at 45watts preheat then 35 watts. During the 45 watt firing the cells voltage dropped to 3.52 volts.
-
3
-
-
What was the voltage of the cells when charging stopped?
There is a setting to stop charging at either 4.1 volts or 4.2 volts.
Maximum puffs is 4.2 volts.
-
What did you do to solve the problem?
-
With Google Chrome or Microsoft Edge (Chromium based) just right click on the post and select "Translate to English"
For Firefox you must add an extension first for translating.
-
2
-
1
-
-
PM sent
-
1
-
DNA 60 (small screen) powered by single 21700
in EScribe, Software and Firmware
Posted
The 18650 battery setting is correct, it more or lees just means round replaceable type cell.
The Cell Soft Cutoff is set at 2.75 volts normally with a round cell.
What is the standing voltage of the cell when it reports 40%?
Can you post a snippet of Device Monitor firing under the conditions described in your post like the one below?
Note on mine the voltage dropped to 3.52 while firing at 45 watts. Had it dropped to below 2.75 volts the low battery error should display.