Kwajr Posted May 5, 2018 Report Share Posted May 5, 2018 No matter what theme even the default I don’t get the replay button to appear Link to comment Share on other sites More sharing options...
Jonski Posted May 5, 2018 Report Share Posted May 5, 2018 What wire are you using ? Link to comment Share on other sites More sharing options...
Kwajr Posted May 5, 2018 Author Report Share Posted May 5, 2018 3316l and I have tried a1 Link to comment Share on other sites More sharing options...
tramog Posted May 5, 2018 Report Share Posted May 5, 2018 Upload the default theme and try again with 316L. Link to comment Share on other sites More sharing options...
Kwajr Posted May 5, 2018 Author Report Share Posted May 5, 2018 That’s what I began this journey with tried this theme when default didn’t work inhave factory test twice and reinstalled escribe Link to comment Share on other sites More sharing options...
RictusGrin Posted May 5, 2018 Report Share Posted May 5, 2018 Are you running the International version? I first thought the US version was the same. It is not even though it shows the Replay option in Escribe. Same thing happened to me. Put the International version on your device and all should be well. Link to comment Share on other sites More sharing options...
Kwajr Posted May 5, 2018 Author Report Share Posted May 5, 2018 Using international Link to comment Share on other sites More sharing options...
schnitzel Posted May 7, 2018 Report Share Posted May 7, 2018 Bad contacts affect replayability as well. If your leads are not screwed tight or the 510 pin is somewhat loose the field will stay blank. Don't know if that's the case with your atty but it's something you can check. Link to comment Share on other sites More sharing options...
Kwajr Posted May 7, 2018 Author Report Share Posted May 7, 2018 Thank you this is what i was looking for don’t have it with me right now but I just wanted to know what conditions will cause the field to be blank Link to comment Share on other sites More sharing options...
Korwin Posted May 10, 2018 Report Share Posted May 10, 2018 Befor you fire first time, field is blank... Link to comment Share on other sites More sharing options...
Kwajr Posted May 10, 2018 Author Report Share Posted May 10, 2018 Yes Link to comment Share on other sites More sharing options...
niandra3 Posted May 13, 2018 Report Share Posted May 13, 2018 For anyone else wondering, you have to take a puff first. That's what Replay is.. you keep hitting your vape until you get that "perfect puff." Then you hit REPLAY to save that puff and it is supposed to re-create it every time. Link to comment Share on other sites More sharing options...
Korwin Posted May 14, 2018 Report Share Posted May 14, 2018 BTW: is there a closed cycle of combinations that repeat over time, or the combination is always random - to know that maybe after 20 puffs I do not need to retest and adjust the watts for a new tuning? Link to comment Share on other sites More sharing options...
embe71 Posted May 14, 2018 Report Share Posted May 14, 2018 What do you mean? There is no "combination" and no cycle. Save puff saves the last puff you took and tries to reproduce it exactly as it was. Link to comment Share on other sites More sharing options...
Korwin Posted May 14, 2018 Report Share Posted May 14, 2018 Yes, but evry puff you try is different , before You save it... Link to comment Share on other sites More sharing options...
Malaysia Posted May 19, 2018 Report Share Posted May 19, 2018 i also got the same...reply field box is blank....any solution of that matter...could anyone ca n help me how to fixed this problem...thank you in advanced Link to comment Share on other sites More sharing options...
niandra3 Posted May 19, 2018 Report Share Posted May 19, 2018 1 hour ago, Malaysia said: i also got the same...reply field box is blank....any solution of that matter...could anyone ca n help me how to fixed this problem...thank you in advanced Try my theme if you want: https://forum.evolvapor.com/files/file/488-clean-black-and-blue-75c250c-wreplay/ It's got a really simple and easy way to use replay. But it also has a replay menu so you can go in and see if it's even enabled. You HAVE to enable Replay in the profile you are using. You also have to use the INTERNATIONAL version of EScribe and the right firmware. All those details are in the description of my theme above. Link to comment Share on other sites More sharing options...
Korwin Posted May 21, 2018 Report Share Posted May 21, 2018 On 19. 5. 2018 at 9:28 PM, Malaysia said: i also got the same...reply field box is blank....any solution of that matter...could anyone ca n help me how to fixed this problem...thank you in advanced ... also check, if you REALY have temp sensitive coil instaled - try different wire... Link to comment Share on other sites More sharing options...
retird Posted May 21, 2018 Report Share Posted May 21, 2018 From the DNA data sheets: Replay is a new feature introduced on the DNA 250C. Replay is intended to capture the flavor and satisfaction of the “perfect puff” and provide the same level of performance and consistency on all subsequent puffs. The use of Nickel, Stainless, Titanium, or other material that increases in resistance when heated is required. In addition, Replay will also prevent dry hits when used with wattage control. To use Replay set the device to the desired power level and operate it normally. Once a satisfying puff is achieved, activate the feature to save and replay the saved puff each time the device is fired. Puff length is not a factor and the user will not be limited to the length of the previous puff. Disable Replay to resume normal operation or find a new puff to save. If Replay cannot be enabled the coil is not compatible. Link to comment Share on other sites More sharing options...
Korwin Posted May 21, 2018 Report Share Posted May 21, 2018 25 minutes ago, niandra3 said: Kanthal also works I believe. Should be in here: https://youtu.be/Jac9au_1uY8?t=8m7s Kanthal works only as a part of multi-wire coils, where other wire/wires are temp sensitive. Link to comment Share on other sites More sharing options...
GHammer Posted May 21, 2018 Report Share Posted May 21, 2018 Here's an easy explanation in a picture. Link to comment Share on other sites More sharing options...
niandra3 Posted May 22, 2018 Report Share Posted May 22, 2018 (edited) You guys are right, sorry. Definitely kanthal does not work with Replay. But yeah mixing kanthal with other TC metals does work (just like normal TC). And apparently you don't have to tell the mod what the material is... no more TCR or anything.! (I always use "wattage" as material for Replay mode) I found the exact quote (useful info): https://youtu.be/Jac9au_1uY8?t=28m37s But again for REPLAY on a 75C, you need latest International Edition of EScribe (currently v2.0 SP15.1) and latest firmware on your mod (I use 1.1 SP33.2). Then you enable Replay in the profile. Then you go to that profile on your mod, take a puff, and the save button should appear. That being said, after trying it for a while I don't really see the appeal. It's just a slightly different implementation of temp control. Edited May 22, 2018 by niandra3 1 Link to comment Share on other sites More sharing options...
Korwin Posted May 23, 2018 Report Share Posted May 23, 2018 I tried the wattage material for Replay profile, it looks like Replay works but at higher power does not work TC, i got dryhits ... if i confirm Temp-sensitiv material u Wattage material table, it turns on curve for Nickel200, so for SS wires probably unusable... 1 Link to comment Share on other sites More sharing options...
GHammer Posted May 23, 2018 Report Share Posted May 23, 2018 3 hours ago, Korwin said: I tried the wattage material for Replay profile, it looks like Replay works but at higher power does not work TC, i got dryhits ... if i confirm Temp-sensitiv material u Wattage material table, it turns on curve for Nickel200, so for SS wires probably unusable... I think you have other problems with your tank/coils/wicking. No idea what you mean by confirm TC material in wattage material table. I use SS430 daily and can assure you that Replay works well with it. Link to comment Share on other sites More sharing options...
Korwin Posted May 23, 2018 Report Share Posted May 23, 2018 Try to compare these pictures - depending on selected Temp-sensing check box You can see different possibility at Profile table - with or without Temperature box under Power settings box... Also compare curves for Nickel200 a Watts under Temp-sensing checkbox... there is no difference Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now