-
Posts
2,610 -
Joined
-
Last visited
-
Days Won
135
Content Type
Profiles
Forums
Downloads
Posts posted by retird
-
-
So it doesn't balance charge in the device?
-
I updated my previous post...
-
Not many folks have a 4 cell 250C. Your cell 3 seems to be out of balance in the screenshot. You might compare this CSV file to your CSV. Save your battery CSV file and load this one (attached file) if you want to see if that helps or you can run battery analyzer to create a CSV for that battery pack.. Screenshot of my 4 cell 250C while still charging:
-
Sorry for the delay.... Storm took out our power and Internet....
Start a ticket with Evolv and they will guide you....
https://helpdesk.evolvapor.com/index.php?a=add&category=1
-
If you don't get these results do a HARD RESET of the device and repeat the previous post again. What are the results? TOOLS/DIAGNOSTICS/REBOOT DEVICE/HARD REBOOT
-
Follow these steps:
Plug device into Escribe and open Device Monitor (no atty attached)
Lower left corner (LLC in later instructions) should say Normal or Charging. If it also says Locked then click the fire button 5 times.
Press fire button once. Voltage drops. No atomizer message in lower center of Device Monitor.
Press and hold adjust button for a second or 2. No Atomizer should appear to the right of Mode in LLC (toward the center of the line, not close to Mode section). Adjust message seen in the Button: category. (lower section of Device Monitor).
Press fire button 5 times. Mode should show Locked (in either Normal or Charge Mode.
Press fire button and voltage should drop.
Press adjust button and where it says Buttons it should say “Adjust”
Press adjust button 6 times… may say “adjust” or “none” beside Button… no change in voltage while clicking 6 times.
What are your results compared to this description?
-
What happens when you take off the pod and repeat the process you described. What do you see in Device Monitor?
What does it say in the lower left corner of Device Monitor?
-
Have you searched the forum for the csv file for those batteries?
You can run Battery Analyzer to create your own.... look for Battery Analyzer under the Mod/Battery tab in EScribe.
-
5 hours ago, Mike91 said:
Installed the update and when I open eScribe it says Orion Plus and gave me the 5 factory presets for DL and MTL but did not give me a 3rd tab for 1.0. Is there something I need to do that will fix this? I am on a Mac and wasn't able to update to the version of eScribe shown on Lost Vape's instructions for the update (running Ver 2.0 SP19 which is all I could find for MacOs), would this affect it?
You might look under the mod tab and see if 1.0 is enabled....
The instructions say: Make sure the software installed is the V2.0 SP20
If you still need help see the last page of the instructions for further help..
-
Simple answer is to periodically charge the device. When not in use a very small amount of current still flows and after long period of non-use the battery is discharged to a level that the on-board charger will not activate. Key is to fully charge before putting the device in mothballs and top off the charge every 4 to 5 months..... another option is if you can unplug a fully charged battery pack (depends on design of the device).
-
Can you save the theme you are using to the computer and post a copy of the file here? Will take a look at it....
-
You might start a ticket with Evolv and explain what happened. Tell them you think the usb connector just needs to be replaced. See what they say. Also tell them the name of the mod and how long you have had it. Here is the link.... https://helpdesk.evolvapor.com/index.php?a=add&category=1
-
You can replace the board.... https://www.evolvapor.com/shop
If you are really skilled in working on circuit boards, and the board is not damaged, I guess you could replace the usb connector....
-
I'll ask again: Does it work just fine while vaping in TC mode on the 250C?
I'll ask again: Can you put the same coil in a different atty and try it on the 250C in TC and Replay modes?
The 250C is different than the 200 and 250.......
Please comment after you do these things....
-
The check atomizer message can mean several things. Maybe the device is built different than the 200 and 250 you have (the 200 and 250 don't have replay either) and there is a connection issue with that atty which will give a check atty message.. Can you put the same coil in a different atty and try it? Note that some atty's don't play well with replay..... here is a link if you choose to visit..... your atty may, or may not be one shown that doesn't play well with replay... https://forum.evolvapor.com/forum/42-replay-and-atomizers/
Does it work just fine while vaping in TC mode on the 250C?
-
hum.... can you save your theme to a computer and install this theme and try it.... maybe something in your theme...
-
Start a ticket with Evolv.... link in my sig line....
-
hum.... you might try opening EScribe than connect your device and see if it will be recognized then you might do a hard reboot from EScribe to see if that helps....
-
Could it be that you have a bad or broken connection in the battery tray or juice leaking onto the board? Can you use a meter and check the voltage at the wires going to input connections going to the board at B- and B+? See diagram in pdf linked here:
-
-
9 minutes ago, mexus said:
It was just the default DNA theme as far as I see, but here you go
OK.... thx..... good to know....
-
9 minutes ago, mexus said:
Thanks. That's what I've figured.
Hope I have time and nerves to develop my ownSince you saved the Triade Theme could you post it here so I can look at it. I'd be interested in knowing what it can do. May be helpful to aid in future questions asked by others.
-
3 minutes ago, mexus said:
I am not versed in designing Themes but if possible and if the functions you want are available for a theme they would need to be designed into the Theme. You might look at the design of your theme and see if Stealth is already there.
There are numerous Themes in the Downloads part of this forum where you can look at the screens and functions and choose the Theme you want. I recommend you save your current theme before changing to another in case you want to go back to Lost Vape Theme. Here is the link for 75C and 250C Themes: https://forum.evolvapor.com/files/category/6-dna-75-color-250-color/
-
I thought that article was probably not correct. There is a stealth mode in the Theme I use with my 250C devices. Here is a screenshot of one screen in Theme Designer. So with the 250C you turn Stealth on and off from the menu. I think Stealth only works when firing the device as you need to see the screen to use the theme. Here is another part of a reddit post I see: Although they do have a lock. But the screen will light up in either case. There is a stealth mode, but it is only stealth when you fire it and not in the menu system.
Charge percentage is off
in Modders' Forum
Posted
So even at 70% each cell isn't balanced?