.thumb.jpg.a21e2bc6a6a2439a8c97330238778481.jpg.881b063a7329fe27fadeaeacdd147081.jpg)
retird
-
Posts
2,610 -
Joined
-
Last visited
-
Days Won
135
Content Type
Profiles
Forums
Downloads
Posts posted by retird
-
-
You can see live ohm's in the Device Monitor also.... just check "live ohms"and see it change while vaping...
-
Link.....
https://forum.evolvapor.com/topic/65933-topic/?do=findComment&comment=892392 -
I would think since Sweet Spots is selling the wire they should be able to give you their csv file....
-
antyac2108 said:
Here you go John the pictures you asked for hope it helps thank you
So with it open like shown in the pictures does it still lock up while firing by pushing the onboard fire button with your finger?
-
Click "File" and "save as"..... is that what you are looking for...?
-
Bern18462 said:
I did that and both are the same ... The lock is off for the ohms and it still fires the coil but with no ohms on screen..
Are you running the latest version of EScribe and firmware update and have you looked at Device Monitor for anything unusual while device is connected to EScribe? -
Did you run Atomizer Analyzer? What was the results?
-
Wick, what hard data have you received on these packs and what results do you have on your testing of the packs? THX
-
Doing this as a option one might choose might be a good idea but there are those of us who change wattage more than temp so as long as it's not the default setting to change temp with up/down buttons it would be just another option I guess...
-
druckle said:
i'M seeing a significant resistance measurement "error" since updating to the 7/9 firmware. For example a coil and device combination that measures 0.25 ohms on a precision ohm meter (and on other DNA devices) measures 0.41 ohms on the DNA 200 with the upgraded firmware. I was not seeing this error prior to the firmware upgrade.
I am also seeing apparent temperatures that are lower than previously observed. I'd appreciate it if you guys could check this. I assume it's not just my DNA 200 device but if it is I'd like to chase down the cause of the error.
FYI, I'm not seeing any deviation with the latest firmware on either beta device and haven't seen any unusual deviation on earlier firmware either. Refinement has been solid at 0.01 ohms. -
Wick said:
Hey, Thanks for the quick response John... The only ones I'm aware of are Hyperion and Hobby King. I only have interest in the Hyperion G6 Premium HvLi Series... They are definitely designed to be charged to a higher terminal cutoff voltage, or so they say
http://media.hyperion.hk/dn/g6hvlipo/default.htm http://media.hyperion.hk/dn/g6hvlipo/HP-G6HvLiSpecSheet042915.pdf Best, Wick Mods
Wick, I have searched for any information on test results for these batteries and found none. Do you have a link to any tests that have been done or statistics relevant to this battery? Thanks -
If that would allow others with normal LiPo's the opportunity to charge them to 4.35 volts then that may not be a good thing.
-
Using Windows 8.1 and USB 3.0 here and seeing no lag in updates at all. No sporadic unresponsiveness of software either.
-
How about a few more pictures of the whole board? May be helpful.
-
I'm in Oklahoma also and always get fast shipping from them too....
-
TheFogginSailor said:
[QUOTE=dc601][QUOTE=TheFogginSailor]I did not have the update, lol, thanks macz!
Anyway, it works with 18650s, but is it safe? Since there is no settings for it..?
Are you planning to connect taps to the balancing connector in your build and using the auxilliary board from Evolv?[/QUOTE]
No, because I´ll use the USB-port for firmware upgrades only.
I dont trust USB-charging on 18650s..
But I am trying to figure out how i get the Battery Meter to work..[/QUOTE]
So reverse battery protection won't be available in your design either? -
TheFogginSailor said:
I did not have the update, lol, thanks macz!
Anyway, it works with 18650s, but is it safe? Since there is no settings for it..?
Are you planning to connect taps to the balancing connector in your build and using the auxilliary board from Evolv? -
Connectors on my builds....Plug and play battery replacement...
-
I've been vaping while connected to charge for hours at a time for a month now....no issues....when vaping the charge symbol (lightning bolt inside the battery meter) on the device goes away while vaping and comes back on about 5 seconds after vaping...
-
Noticed also that everything in the battery section greys out and no adjustments are available when power supply is selected...
-
SSV, what wire are you talking about?
-
Hello everybody. Looking forward to this forum being populated with a lot of information and a place to share.
EScribe Software
in EScribe, Software and Firmware
Posted
druckle, mind if I ask what device you have? I've been trying to replicate what you are seeing on a reference device and can't get it to act up. thx