DNA and MESH SS316L

[Klap]

Hi i am working with the RTA THEMIS of DIGITAL FLAVOR and MESH SS316L , i have 0.128 ohms,  But i can't work fine the MESH TCR or Replay.

 Someone have the Profile for this Material for work fine in TCR mode or REPLAY MODE? 

Thanks !!!!

 

 

Edited February 1, 2019 by Klap
add images

[retird]

Digital Flavor website.....  Themis.....   http://digiflavor.com/project/themis/

Contact Us info:   http://digiflavor.com/contact-us/

You might contact them and ask for the TCF, TFR, CSV  for their SS316L mesh you are using.....  ask them also if the mesh has worked in Temperature Control and Replay Mode....  Please let us know what you find out....

[Lanzarotechris]

30 minutes ago, retird said:

Please let us know what you find out.... 

Yes, that would be nice. Mesh data is so difficult to find on the web.

I have an Iris Mesh RDA and I really like it. Uses lots of cotton but the vape is great.

I searched a lot but never found any useful info. Not even what will be the difference in vaping when using 150, 300 or 400 mesh,

or how to get a certain resistance. Its still some kind of surprise what you'll get when you make the coil.

If someone knows a dedicated webpage about mesh I would be thankful.

[Klap]

OKEY, i will ask to Digi for the information, if i have an answer i will post here  

[redduc900]

The TCR should be 0.00092 just like any other SS316L wire.

[Klap]

Hace 10 minutos , redduc900 dijo:

The TCR should be 0.00092 just like any other SS316L wire.

i will try in Escribe and send to my DNA. i am waiting for Difgi Answer to  thanks !

 

[Klap]

u think this CSV is fine? 

Mesh.csv

[Wayneo]

Klap Using Device Monitor with Cold and Live Ohms ticked, what are the starting and ending values (while taking a puff)?

Replay does not require a material profile.

If you want the  resistance to change, cut off some of the width (Not the clamped ends).

[Klap]

okey, let me give this to you i dont know if i do fine:

 

 

I fire for 3 seconds

 

 

 

i see cold is in 0,118 and when i puff go to 0,136 

[Wayneo]

Thanks for the printscreens. It looks to me that Replay should work, and I see you have replayed thousands of puffs. Have you used  this same profile successfully to replay other atomizers.

EDIT: OR just post a printscreen of Profile 6

[Wayneo]

Ya know, in your original post you said

On 1/31/2019 at 7:08 PM, Klap said:

But i can't work fine the MESH TCR or Replay.

My response was only with regards to Replay, and you show me Profile 2, not 6 (which was bolded), but now you tell me Replay does work. Either way, the csv you posted should just be thrown out. Try to use the standard SS316 material profile on your mod.

Edit: Added more info for you

I have no clue about your mod and customizations done by the vendor. So this refers to Evolv defaults.
In your Profile 2, change the Material back to watts
Profile 6 should be your SS316. Try your mesh there in TC
Profile 4 is Nickel which you probably don't use, so you can jiggy with that one if you must.

[darkneovamp]

On 1/31/2019 at 7:08 PM, Klap said:

Hi i am working with the RTA THEMIS of DIGITAL FLAVOR and MESH SS316L , i have 0.128 ohms,  But i can't work fine the MESH TCR or Replay.

 Someone have the Profile for this Material for work fine in TCR mode or REPLAY MODE? 

Thanks !!!!

 

 

I have the same setup as you.  I found that the Digiflavor mesh would not read or work properly with TC or Replay.  I ordered some Vandy Vape SS mesh and it works as it's supposed to.