craigmaque Posted September 10, 2018 Report Share Posted September 10, 2018 How can we get the version of escribe that supports the DNA go board. I definitely need to mess around with the settings with nic salt I think. I want to add more power to my DL setting also. Link to comment Share on other sites More sharing options...
Vcsoto Posted September 10, 2018 Report Share Posted September 10, 2018 I may have been a bit too much in crisis mode, but I opened up a ticket and got this link:https://downloads.evolvapor.com/SetupEScribe2_SP17_US_ServicePack_Go.exe Hope this helps! Link to comment Share on other sites More sharing options...
WozniakMac Posted September 10, 2018 Report Share Posted September 10, 2018 I got the same info from them. I installed Escribe 15.1 and the installed this Service Pack, but my Orion still isn't recognized. Can someone help me with this? I need to raise my wattage too. Thank you and have a great day. Link to comment Share on other sites More sharing options...
Vcsoto Posted September 10, 2018 Report Share Posted September 10, 2018 1 minute ago, WozniakMac said: I got the same info from them. I installed Escribe 15.1 and the installed this Service Pack, but my Orion still isn't recognized. Can someone help me with this? I need to raise my wattage too. Thank you and have a great day. Link above should take you right to the download for the new Escribe, Lost Vape FB page and the Early Firmware thread has it as well. Hope that helps! ....now if I could only figure out why the .5 ohm pod isn't getting the wattage I choose for it, I would be a happy man. Link to comment Share on other sites More sharing options...
WozniakMac Posted September 10, 2018 Report Share Posted September 10, 2018 (edited) I have the software, but my device isn't showing inthe software. How did you install yours to get it to work? Edited September 10, 2018 by WozniakMac Link to comment Share on other sites More sharing options...
Vcsoto Posted September 10, 2018 Report Share Posted September 10, 2018 Just now, WozniakMac said: I have the software, but my device isn't showing inthe software. How did you install yours to get it to work? PC or Mac? Link to comment Share on other sites More sharing options...
WozniakMac Posted September 10, 2018 Report Share Posted September 10, 2018 PC Link to comment Share on other sites More sharing options...
Vcsoto Posted September 10, 2018 Report Share Posted September 10, 2018 Just now, WozniakMac said: PC When you go to Help/ About Escribe, what SP version does it show? Link to comment Share on other sites More sharing options...
WozniakMac Posted September 10, 2018 Report Share Posted September 10, 2018 It shows Version 2.0 SP17. Link to comment Share on other sites More sharing options...
Vcsoto Posted September 10, 2018 Report Share Posted September 10, 2018 Sorry man, looks like you have everything good, only thing I can think of would be a bad cable or port, but mine just popped up once I plugged it in the first time. Sorry I couldn't be of much help. Link to comment Share on other sites More sharing options...
craigmaque Posted September 10, 2018 Author Report Share Posted September 10, 2018 2 hours ago, Vcsoto said: I may have been a bit too much in crisis mode, but I opened up a ticket and got this link:https://downloads.evolvapor.com/SetupEScribe2_SP17_US_ServicePack_Go.exe Hope this helps! Thank you very much 1 Link to comment Share on other sites More sharing options...
Droopydroors Posted September 10, 2018 Report Share Posted September 10, 2018 I actually didn't have luck with the supplied cord. And also I think your battery has to be out of the "red" for it to connect without issue. Just guessing but I have had better luck with higher battery. Link to comment Share on other sites More sharing options...
James Posted September 10, 2018 Report Share Posted September 10, 2018 The Go will show up on USB for the first hour after the cable has been plugged in. (After that, it disconnects from USB Data to conserve energy.) Link to comment Share on other sites More sharing options...
Droopydroors Posted September 10, 2018 Report Share Posted September 10, 2018 Ok so it seems as though it must have been another cable that wasn't working well. I pulled my PS4 charging cord and now it is connecting Everytime without issue. 1 Link to comment Share on other sites More sharing options...
WozniakMac Posted September 10, 2018 Report Share Posted September 10, 2018 1 hour ago, Droopydroors said: I actually didn't have luck with the supplied cord. And also I think your battery has to be out of the "red" for it to connect without issue. Just guessing but I have had better luck with higher battery. This worked! I got a cable from my Mophie charger and it worked fine. I updated my settings and this thing rocks after the wattage adjustments. Thank you so much! 1 Link to comment Share on other sites More sharing options...
Droopydroors Posted September 10, 2018 Report Share Posted September 10, 2018 Just now, WozniakMac said: This worked! I got a cable from my Mophie charger and it worked fine. I updated my settings and this thing rocks after the wattage adjustments. Thank you so much! Good!!! I'm glad it worked. It seems very sensitive to cords. I had one cord that worked earlier today and then it didn't work a few minutes ago so I used a different cord that seemed to be a bit more snug and it worked without issue. I did notify Lost Vape that they should supply a USB data cord with the Orion. Link to comment Share on other sites More sharing options...
WozniakMac Posted September 10, 2018 Report Share Posted September 10, 2018 It's a shame they give us a bad cable for a great device. The device is great though. This is exactly what I was wanting after trying many mods and tanks. I will use this all day now. Link to comment Share on other sites More sharing options...
FrankV Posted September 11, 2018 Report Share Posted September 11, 2018 Mine won’t come up on Escribe. I have a version just for my 250C but I’m not sure if that’s the same software. Can’t find anything about the DNA Go chip on the first page. Anyone have any help or have the software for Mac? Link to comment Share on other sites More sharing options...
dwcraig1 Posted September 11, 2018 Report Share Posted September 11, 2018 https://downloads.evolvapor.com/SetupEScribe2_SP17_US.pkg https://downloads.evolvapor.com/SetupEScribe2_SP17_INT.pkg It's way down near the bottom on the Early Firmware page Link to comment Share on other sites More sharing options...
Droopydroors Posted September 11, 2018 Report Share Posted September 11, 2018 3 hours ago, FrankV said: Mine won’t come up on Escribe. I have a version just for my 250C but I’m not sure if that’s the same software. Can’t find anything about the DNA Go chip on the first page. Anyone have any help or have the software for Mac? The firmware needed is literally the second post in this thread. Link to comment Share on other sites More sharing options...
FrankV Posted September 11, 2018 Report Share Posted September 11, 2018 35 minutes ago, Droopydroors said: The firmware needed is literally the second post in this thread. No it isn’t. That’s an .exe file that won’t work on a Mac. I would have not asked if that file worked. Link to comment Share on other sites More sharing options...
FrankV Posted September 11, 2018 Report Share Posted September 11, 2018 (edited) 3 hours ago, dwcraig1 said: https://downloads.evolvapor.com/SetupEScribe2_SP17_US.pkg https://downloads.evolvapor.com/SetupEScribe2_SP17_INT.pkg It's way down near the bottom on the Early Firmware page I didn’t see this on the website my apologies. Thank you for the links. This worked perfectly and my device connected right up on my Mac! Edited September 11, 2018 by FrankV Link to comment Share on other sites More sharing options...
philbh Posted September 28, 2018 Report Share Posted September 28, 2018 No luck for me. Installed the latest version with sp17. Tried 3 cables that I know are good, in 2 different ports. 1st time with Escribe, not going well... Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now