ej2_sir Posted March 3, 2017 Author Report Share Posted March 3, 2017 Hi, struggling with my dna75. In Tc ss316l, the screen just displays 'off' rather than the temp rising..... It still vapes but obviously im not sure its regulating temp? Any ideas? I factory reset not long ago and only changes I have made are case analysis and set the internal resistance (0.004 if i recall). Thanks Link to comment Share on other sites More sharing options...
VapingBad Posted March 4, 2017 Report Share Posted March 4, 2017 It is not sensing the resistance rise enough in the first 2 seconds, it wast to see a 185 F raise in temp or it will drop out of temp protection, well partially drop out it still enforces some limits. It could be a connection issue clean and tighten, disconnect the atty, press fire to clear the atty memory, it could also be an internal wiring or grounding issue. You mod res seems reasonable. Link to comment Share on other sites More sharing options...
ej2_sir Posted March 4, 2017 Author Report Share Posted March 4, 2017 Thanks for the suggestions! Gave the 510 and battery cap a good clean with alcohol and it seems better.... Link to comment Share on other sites More sharing options...
gogo Posted March 9, 2017 Report Share Posted March 9, 2017 hello i have big problem with that off message on vt inbox ....every change of coil or is constantly showin off or first second then start to count celzius but problem is i set for example 230 or 260 c it wont go higher then 190 then i connect to escribe click restore button hope it go on factory setting then i probably f*** up everithing no second welcome screen first is evolv dna76 then vt inbox no more that second could someone send my plesa ....and tem control doest work how it should.... does enyone have some link or could send me softweare to upload on mod to work properly please some kind full setup for dna75 or for wire ss316 it is so frustraiting iam not computer guy i dont know how to use all that but so much issues with dna and so more money given for it or someone have knowlage about that and have some will to help me and guide me tru what i must to click we could her over phone over wats upp viber messanger how ever just is there any who can help my i couldnt find enything usefull online my mail is ggunikatni@gmail.com and phone is +385916215075 it will be easyer for bouth and me to describe my issue and you to help me and guide me what to click please if is there any one who is willing to help i am desperate Link to comment Share on other sites More sharing options...
giz_60 Posted March 9, 2017 Report Share Posted March 9, 2017 Here is the factory .ecig file for the VT Inbox75... Hcigar_VT_Inbox_75.ecig Link to comment Share on other sites More sharing options...
gogo Posted March 9, 2017 Report Share Posted March 9, 2017 what to do with that i have that but what ever i sett it wont work can you please csall me or give me your number i call you Link to comment Share on other sites More sharing options...
giz_60 Posted March 9, 2017 Report Share Posted March 9, 2017 In Escribe, go to 'File>Open' and choose the .ecig file & it will load into Escribe. Then click 'Upload To Device'Edit: Read post #2 above...?? Link to comment Share on other sites More sharing options...
gogo Posted March 9, 2017 Report Share Posted March 9, 2017 em i stupid or what i cant find it where to go haw to set that pllease could you call me over internet social media up is my nnumber Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 ooooo igot it now i just seting up i will write here if i done it thanks Link to comment Share on other sites More sharing options...
giz_60 Posted March 10, 2017 Report Share Posted March 10, 2017 Top of screen in Escribe is...'File' 'Edit' 'Internet' 'Options' 'Tools' 'Help'....Click 'File>Open' the pick the .ecig file... Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 i do how you sed all i set temperature set preheat set watts i see it have welcome message inbox weee up?ouid to device now lets seeee Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 hmmmm i set 35 w and 230C but still it want go higher then ....150 i i just have dry hit it didnt show me temp protect it was showing when cotton was like dry and thet off is stil there Link to comment Share on other sites More sharing options...
giz_60 Posted March 10, 2017 Report Share Posted March 10, 2017 Off means it is switching from 'Temp' mode to 'Power' mode...check all connections...clean 510 on mod & attomizer with alcohol...clean battery terminals inside mod... Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 is it matter in which profile i set ss wire i put on profile 2 on generak card Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 i Å¡utt screen on profile 2 ohms material baterry prosent up?oad it wont show me on mod it shows vats and ampers and that off is still there no change in setings just second welcom screen ..........it is clean and 510 and pin everything is so clean buff doesnt stops Link to comment Share on other sites More sharing options...
retird Posted March 10, 2017 Report Share Posted March 10, 2017 Here is an older tutorial but may help..... https://downloads.evolvapor.com/escribe/guide/story.html Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 at least it showing in screen what i set ohm material present baterry but... it is set on preheat 50 power 35 230 C hit fire botton and offcourse off and again dont want to count up celzius it sed how i wrote to 230 it go only to 150 why and what is hapening with this piece od uffffffff Link to comment Share on other sites More sharing options...
Wayneo Posted March 10, 2017 Report Share Posted March 10, 2017 @gogo No need to be desperate. SS is very safe to use in wattage/kanthal/regular mode. I'd suggest you follow post 16, then some youtube videos about your mod/DNA device, get comfortable with it, then worry about TC vaping .... you'll get there. Relax and have a vape. Link to comment Share on other sites More sharing options...
giz_60 Posted March 10, 2017 Report Share Posted March 10, 2017 Try this...set preheat to 75w..punch to 11 for 3 seconds....power to 75w @ 230c Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 ill try but i think it gons kill my baterry because i ue simple wire and wape on low watts and celzius ok i sam going to try Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 no use it is harder and all that but it still wont count celzius up Link to comment Share on other sites More sharing options...
giz_60 Posted March 10, 2017 Report Share Posted March 10, 2017 Temperature mode is completely different from wattage mode...as @retird said...you can vape in watt mod until you get comfortable with your device & then learn temperature mode...factory wattage mode on the inbox is profile #6 Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 everything that is ok i understand but it bother my why is not work properly i know temp mode all of it but mod is acting wierd that is problem i try to set it right but i cand how ever i try Link to comment Share on other sites More sharing options...
giz_60 Posted March 10, 2017 Report Share Posted March 10, 2017 go to your profile...there is a box to check beside 'Temperature-Dominant'...check that & upload to deviceEdit: can you post a screen shot of your profile? Link to comment Share on other sites More sharing options...
gogo Posted March 10, 2017 Report Share Posted March 10, 2017 again it by it self change screen look i set prosents of baterry it shows me vats Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now