mstave Posted May 6, 2017 Author Report Share Posted May 6, 2017 1 Link to comment Share on other sites More sharing options...
dywersant Posted May 16, 2017 Report Share Posted May 16, 2017 Thanks, this will come in handy in a week or two. How did you measure 510 resistance ? Link to comment Share on other sites More sharing options...
Sank Posted May 18, 2017 Report Share Posted May 18, 2017 hi mstave l get the same hcigar box, and get some problem too, your box work fine with 3cells? Link to comment Share on other sites More sharing options...
mstave Posted May 23, 2017 Author Report Share Posted May 23, 2017 Measured the internal resistance using a copper dowel, with a milled 510 connection. Set internal resistance to 0 in Escribe, invoke the atomizer analyzer, screw in copper plug until read resistance settles - that is the internal resistance. Haven't used the mod in 3 cell mode at all yet Link to comment Share on other sites More sharing options...
Canadianvape Posted June 27, 2017 Report Share Posted June 27, 2017 Thanks, I've been looking for this information for 12hours, most appreciated Link to comment Share on other sites More sharing options...
Wayneo Posted June 27, 2017 Report Share Posted June 27, 2017 @mstave With all due respect, I have found a copper tool is no longer an accurate tool for the 2xx series measurement ever since the Feb 2016 updates. With mine from smokefreemods.com, after Feb 2016, it would go to ~.006 then a ?. At the latest firmware, I'm also getting around the same (0.006 or 0.007) but no longer a '?'. I did retest my boards with the method below and get the same results as I already had before (0.002-0.006) while AA worked. Starting around here -> giz_60 alternative mod resistance calculation (March 10 post) 1 Link to comment Share on other sites More sharing options...
mstave Posted June 27, 2017 Author Report Share Posted June 27, 2017 (edited) Never had any issues with the copper milled plug. Looking at the thread you posted, I am doubting any mod with a DNA board having an internal resistance over 0.14ohms. Edited June 27, 2017 by mstave clarity Link to comment Share on other sites More sharing options...
Wayneo Posted June 27, 2017 Report Share Posted June 27, 2017 I guess that must've been the wrong link, only showing the wire. In another thread it's mentioned to subtract the cold ohm value (.142) from the raw ohm value (.145), leaving a .003 which matches the copper plug. Sorry 'bout that. Link to comment Share on other sites More sharing options...
Canadianvape Posted June 29, 2017 Report Share Posted June 29, 2017 On 2017-06-27 at 1:20 PM, Wayneo said: I guess that must've been the wrong link, only showing the wire. In another thread it's mentioned to subtract the cold ohm value (.142) from the raw ohm value (.145), leaving a .003 which matches the copper plug. Sorry 'bout that. So 0.007 or 0.003? Link to comment Share on other sites More sharing options...
Wayneo Posted June 29, 2017 Report Share Posted June 29, 2017 Read my prior post. Link to comment Share on other sites More sharing options...
Canadianvape Posted June 29, 2017 Report Share Posted June 29, 2017 (edited) 4 hours ago, Wayneo said: Read my prior post. Thanks, had to re read it as some of the technical content was being a bit hazy. I'm gonna go with 0.0032, unless anyone can provide the actual 4th point Edited June 29, 2017 by Canadianvape Previous comments started to click Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now