[Adding new fonts to Theme Designer]

11 hours ago, croyleje said:

I want to add two right now the 8 bit font and a cartoon font.  There is obviously a way to do it or a workaround because there are themes with fonts not in the list.

you add fonts to the windows font folder and they will automatically install , when you reopen theme designer that should be in the drop down list - occasionally windows will not recognise or read some fonts because of compatibility or the font size will not appear at all because they are not available in that size you want them to be in - try to download a similar or a different source to where you get the font from

[Custom Fire Button]

ok i thought it might no be right , just thought its firing and just doing the same job a coil would do but i had my doubts - thanks again

[Custom Fire Button]

could i use this to run a battery analyzers when i do a battery profile or does it have to be a coil ?

 

its an inline voltmeter

[Custom Fire Button]

thankyou

[Custom Fire Button]

ok im well away building my own box , now i have bought i fire button to wire on to the pcb , i know which is positive and negative on the board but the fire button just has 2 pins with some tiny writing on the back and i cant make out what it says even using a magnifying glass but it does not look like positive or negative  or symbols that would look like a minus or plus , does it matter which pin is the positive or negative on the fire button ?

[OEM and retail 250C Chip]

great find retird much appreciated for the info thanks guys

[OEM and retail 250C Chip]

Thanks for the info and the link 

[OEM and retail 250C Chip]

so there should be no difference between a retail chip and a retail manufactured chip , same terminals and everything as obviously my box mod hasn't got the wired fire button but uses the touch pads to fire , if i get an enclosure then i would have to wire the fire button up with new actuator fire button and would escribe pick up the new battery config because i plan to use 2x21700 instead of 2x18650 , with a new battery sled . also i've seen those fire buttons which aluminate is it same terminal and wiring as a normal fire button you would wire

 

thanks for the time

[OEM and retail 250C Chip]

Hello , is there any difference between a chip installed from a manufacturer and one you can buy retail from Evolv - could i take a chip out of a ready made box with a 250C in it and install it in a custom enclosure , the mod box i have at the moment has a full set of actuators buttons but the enclose would require me to solder a wire from fire button up to the pcb board 

[Dna250c Error Press Up]

On 11/12/2018 at 5:59 PM, Wayneo said:

@James , my mod with SP35 (told you about this earlier) did not exhibit this until after I created a new screen on the Evolv default theme and had it set to 'return to parent'. After changing that option to 'return to main screen' all is fine at SP35. That mod is still at SP35.

Reviving an old thread but i suffered the same problem with error up message every time i uploaded a theme or firmware to my device but everything worked as it should even though it displayed error up message , the device in question is a vapecige VT250C i now have 2 of them one gives this error up message the other one doesn't  , i read this thread and tried Wayneo's solution as my lock screen hadn't got anything assigned to it so i assigned  round robin and it fixed the problem of the error up message  

[What mean?]

Warmth of replay - numbered 1 to 11 like how boost interacts with non temperature controlled coils

[learning how to create a personal theme]

Best way to learn is understand the original default themeworks , learning what each setting does familiarize yourself with how the menu works and the settings in escribe where your profiles are located , then download another theme whichever you like  and make small changes like wallpaper or the way the layout is positioned make small changes - then understand how the theme is configured looking at how each setting is configured and how to replicate it , it takes time and with time each theme you make will become better with time

[Clicks to unlock and lock device]

thanks just clearing things up i need to add something on my theme

[Clicks to unlock and lock device]

need some feedback on your DNA devices - so appreciate it - how many clicks to unlock your device ? the default is 5 clicks  to unlock and this cannot be changed in therme or escribe - am i correct

so unlocking the device will always be 5 clicks and if you change clicks on the device its to lock only it will not affect the unlock sequence of 5 clicks because this is a default and cant be changed in theme or escribe and also let me know if your using INT version of escribe or US version and what service pack if you can alter unlock sequence either in escribe or theme itself

[Presets?]

1 hour ago, Richieriotoffit said:

@formula 1Thanks mate that's what I was after, I got a bit of a bashing on another thread for asking this same question. I said there I struggled with mental health issues and my concentration along with post traumatic amnesia makes even wording simple sentences an issue the vape community as a whole can be a lil self righteous at times it makes me mad so thanks dude for all your help. If you don't mind I'd like to use the theme u use also is it available? 

no problem , my themes and other users themes are available in the download section here https://forum.evolvapor.com/files/  alternatively if you want my themes you just need to click on my profile and look for uploaded files.

[Presets?]

7 hours ago, Richieriotoffit said:

OK great guys thanks I think lol. So what Im thinking is I have to create "profiles" on my laptop and upload to the device? Say profile1 for a rda, profile2 for a different rda, profile?? for another 1 etc? Am I right? 

you can do that if you wish but make sure you backup your original settings , i suppose its one way to get a round pre determined setting for your particular needs

[Presets?]

on my theme or where it has the profile tab on top , here in the photo its called profile one where on the device it may say watts , SS316 or replay etc - to select this tab is what you do when altering wattage , you navigate the menu by the 3 buttons or two buttons on your device and the 2 outer buttons  act as up and down and the middle is to select or highlight that particular setting as you would do for changing watts and once select you use the outer button again to change values or cycle the profiles

[Presets?]

you can go into escribe and preset the profile setting wattage and pre heat and replay on all other features that the material you choose can start off with like a basic level you cant start from like setting the watts to 50 or 60 and preheat options to a required level before altering them on the device ,  that's as much as a preset you can do - changing materials or swapping tanks will always trigger the new coil detected which you have to set - as the photograph shows where to alter the default levels

 

[Conditional Automatic Toggle]

cant remember off the top of my head if the standard default theme has those options or toggles , but two of my themes i have uploaded just recently have, the green skulled vaporizer themes and chameleon download them take a look how the toggles are configured and add them to the default or a theme of your choosing through theme builder  , basically when you get the hang of theme builder you can more or less add what you like so long as the options are available in the drop down menus and you just edit and add to your chosen theme as you with the picture under "DEVICE" page it has keep screen on and brightness options which in this theme is called SCREEN

 

 

[Lost Vape Drone 250C issues.]

5 hours ago, etab75 said:

UPDATE

I have taken the mod apart and dried out the internals. Removed the tape which was under the plastic plate and covering the screws now you can see inside the 510 area - quite handy to see if anything is going wrong. The leaking stems from the seal around the centre pin when an atty is screwed on. I saw a video where this area had a drop of sealant placed upon it thus stopping the leaking. Not a perfect solution but it will suffice - its back in use and no problems so far.

See video here for reference, similar disassembly though different model: 

 

 

Cheers for the replies.

your drone looks different to mine its not as see through as yours at the top did you buy it new ? mine is relatively see through but has a plate underneath this bit you show

[Lost Vape Drone 250C issues.]

no problem with my drone , i would say you've got a dodgy one , apart from the design flaws its the best squonker on the market if you can overlook the flimsy battery door and be aware of it , the fiddly replacement of the squonk bottle can be difficult to easily place in and out but i use the ceramic tweezers and takes a couple of seconds apart from that looks lovely in ultem and silver takes dual 18650 and has a DNA chip and fits a 30mm rda or rta with ease no many squonkers can boast that

[Lost Vape Paranormal Evolv DNA 250 Color Battery Problem]

plus i forgot to mention you can monitor the battery to see how many amps it pulls when firing either through the theme you use or in escribe in every time you fire it

[Lost Vape Paranormal Evolv DNA 250 Color Battery Problem]

1 hour ago, k3kz3 said:

here. look at that -> https://drive.google.com/file/d/1hQG7lB0bpVZYXtikjNQtmGI2MYNodyG9/view?usp=sharing

 

thats my Battery life

i would start by buying a standalone charger and if you get the same results i would buy another pair of batteries and compare the two , it may well be the battery isnt getting enough charge or you may have a faulty set or even fake pair of batteries , if you get the exact same batteries and they charge or perform better using the stand alone charger then i would return the other batteries to the vendor you bought them off , then we can rule out one thing at a time

[Lost Vape Paranormal Evolv DNA 250 Color Battery Problem]

9 hours ago, k3kz3 said:

Hello Guys,

 

i've searched the whole day yesterday on the internet about anyone who have the same Problem...

got my new EVOLV DNA 250 Color (Lost Vape Paranormal) and bought 2 new 18650 Batterys for it to use it with my top coiler.

The Problem is, the battery is charging very very slow in that mod. but the bigger problem i got is the lifetime!!! i can only use it (on 70W with dual coil on 0,25ohms only for 2-3 hours if i use it often.

the same Batterys in my Crown 4 with the same Deck have an lifetime over 6 hours or more...

i used the battery analysis this night to make a profile for these batteries. but nothing really changed 😕

 

anyone knows why my lifetime is so bad in this Mod? is that normal for an 200€ Mod? 

 

Thanks for your help!
I really love all the functions on escribe and the design... i don't want to give it back and change it to anotherone

 

 

i wouldnt advise charging the batteries via the mod for safety reason and life span ,( although plenty do) its always recommended to have a stand alone charger  , i hope youre using the usb cable that came with the device and not a mobile phone charge or anything of that nature as sometimes the amperage is different to what the device  needs and then there is the right type of batteries yes you can use any 18650 but better the amperage , better the mah and that results in how long the batteries last and how often and how quick they charge and buying from a trusted source theres alot of fake batteries out there - any device like the DNA 250C would require Samsung 30Q batteries with something like 30 amp discharge and 3000mah or anything equivalent to those figures 

 

[Paranormal 250C Puff Counter]

What's he asking then ? is it possible to have a puff counter ? on the screen - well yes it is