-
Posts
2,322 -
Joined
-
Last visited
-
Days Won
146
Content Type
Profiles
Forums
Downloads
Posts posted by dwcraig1
-
-
In EScribe under the screen tab you can set it to show pack voltage.
Perhaps increase your cell soft cut off. -
Well it's for sure better to not be taking your battery all the way down but 18650's are cheap and easy to replace, maybe carry another battery in a battery box if a charger isn't handy.
-
What it drops to under load is of concern, less than 2.5 volts would not be good for the battery. Do you get the "weak battery" message or with the newer firmware the battery symbol flashes?
-
Is this during use or is it draining while not being used for a while?
-
Since it is close to the same (same actually) to what readings I got with tha DNA 200 I don't see any problem. Thanks though.
Had I measured the voltage where the 510's wires are soldered to the board there probably would have been a different reading.
The main grit of my post was that the output measured was the same on the DNA 200 with both firmware. -
For what it's worth I just did a little testing using a Magma RDA. I used my VTbox200 running SP3. Using EScribe voltage readings and a volt meter on the RBA's posts. I then rolled back the firmware to 2-23 and compared the two.
I also used an IPV2 and took voltage readings off the posts of the RDA.
Wattage set at 45 and temp off
EScribe with both firmware said 4.75 volts, the voltage readings off the RDA's posts were the same also, 4.39 volts.
Voltage readings taken from the RDA posts on the IPV2 also was 4.39 volts. -
So my Kanthal with preheat didn't seem to work with SP3 so I went back to "recommended" and it worked. But then I flashed it back to SP3 and preheat with Kanthal works. This is with a DNA200.
-
That's best if it can be done, will advise more if needed on how.
-
yes but here:yoseff said:
This is what you refer to?
Even after new firmware we continue cheating on our beloved DNA's...
Will confirm later if it still works.
https://forum.evolvapor.com/topic/65540-topic/?do=findComment&comment=884720
It worked for me with the FW before... let me try it..one moment
Edit: I couldn't get it to work on the two 200's that worked before, it can be a bit finicky, I'll try again later -
There is such a way
-
I'm going to do one using a flask clone later this year I think using the small screen one.
-
954kevin said:
thanks craig. i see in the description it updates the escribe software, does it also make changes on the board in my mod that allows it to work better in tc?
Among a few other things it will make SS3XX work smoothly. -
https://forum.evolvapor.com/topic/66731-topic/?do=findComment&comment=900119954kevin said:hey gang, sorry for the needed explanation, but how and where do i get this new improved firmware n put it on my efusion duo? does this update only affect the ss tc? i mean ive never done a firmware update, ive only had this, my first dna200, for a few weeks. im still learning. i do use ss316l in tc exclusively so i would love to get this update. thanks in advance for the help!!!
The one listed as "Early" 2016-08-08.....just listed -
Should it only work on a Vapor Shark?I thought I'd give it a try (on my VT133)
here is snip:
Should it only work on a Vapor Shark? -
Mine, Vtbox200, and some others had a bit of e liquid between the JST connector that's on the board and the board doing some minor conducting causing cell 3 to drain slowly if sitting a few days.
-
^^^^true but still might how the ).0016? came to be.
-
I'm surprised this wasn't mentioned before so here goes. I just checked my SDNA 75 again for mod resistance, not only was I wanting to see than it was still 0.002? but wanted to see how many digits the the right of the decimal point it reads and it's 3. So how did DJSLB come up with ).0016?? Just something I was thinking about, perhaps he measured it with other means.
-
The way I see it there are only a few reasons that would make it "necessary" to upgrade to this latest software/firmware, you have a DNA250 or DNA60, SS3XX is your go to wire.
I upgraded all of mine regardless, my go to wire is SS430 Ni free, it worked good with the recommended firmware. Just saying. -
Much better and consistent with what others are reporting.mactavish said:I edited my first post above with RETEST RESULTS, using the latest Escribe version 1.2. Got 0.002 INSTEAD of 0.006.
-
Be sure to let us know your results.
-
I would try a reboot first, Steve explains reverting the firmware pretty well here:
http://vapingunderground.com/threads/hcigar-vt133-dual-18650-dna200.171476/page-74#post-1307253 -
This one?txmonkey214 said:Hi, If you look on their website, the V5's are designed for use in unregulated mods. I recently bought a 22mm V4 to build a DNA 60 mod. I have hear evolv designed one with 4 screws mounted into the mod body. But, I haven't had any luck finding them online.
http://www.protovapor.com/product/evolv-510-connector/- 1
-
I'm guessing the 60 will be in a different case, just a guess though.
-
I'm not sure how many 250's are available but there's one less black one now.
Early Firmware and EScribe Suite Discussion Thread
in EScribe, Software and Firmware
Posted
While I have no 316 I used 317 which has a slightly lower TCR and got an 18% change in resistance between cold and 430F.