[HCIGAR VT133 worth buying]

Probably better than average.

[HCIGAR VT133 worth buying]

I paid $80 USD for mine, they list for double that. Sounds like a deal to me.

[DNA 250]

Here also, depending on shipping charges they may be a bit less than Amazon.
http://www.ebay.com/itm/PortaPow-Specialised-3-3ft-20AWG-Charge-Only-Micro-USB-Cable-2-Pack-New-/282068762006?hash=item41ac9bbd96:g~oAAOSwepJXYQK7

[Smy dna 75 not great]

I think quite a few of them have the screen off a bit, mine's not too bad but is crooked.
I have 3 Bellus' and all of them screw flush as well as anything else I tried fit flush.
By pushing in the 510 pin on the mod with a small rod does it seem to have the expected travel?

[SMY DNA75 soft cell cutoff.]

I left mine there. I think most did also.

[Help dialing in my Vt133]

Maximum voltage on a DNA200/250 using 2 cells is 6 volts (9 volts with 3 cells)
On the DNA75 it is 6.2 volts
DNA40 & 60 output to 9 volts

[Steam Engine TC Precision Number Meaning]

My thoughts on the reason for 316 being in demand more than 430: 316 is a higher grade used for medical equipment. 316 was being used with mechanical's early on as it is what was availible (welding wire) Just my opinion here.
The resistance change between cold and hot coil is to be considered, the more change the easier for the board to work with it.

[Therion USB - no luck connecting]

rupert.n said:

Amazing, that did it, thank you very much.

The version of EScribe that you were using is only for the DNA200's
You will probably be looking for the mod tab, go to "Options" and "User Interface" and select "Manufacturer" from the drop down menu.
Edit: made a correction

[Therion USB - no luck connecting]

https://downloads.evolvapor.com/SetupES.exe
Try this.

[DNA 75 will not go to 'sleep' - Any ideas?]

I guess that part really doesn't matter, my thoughts were something wet and gooey on the board like flux or juice conducting micro voltage from part a to part b, something along those lines.

[DNA 75 will not go to 'sleep' - Any ideas?]

Is this a factory built mod or did you build it?

[DNA 75 will not go to 'sleep' - Any ideas?]

What happens with an external charger?

[Dna133/200 lower watt batt efficiency]

rbtx is in Orange County, Ca.

[Escribe setup for VT133]

dleone32 said:

Is this a general setting to use for the DNA 200? Should I use it?

This is the settings for Steve's Hcigar VT133.
What DNA200 mod do you have?

[Atomizer analyzer???? It's gone...]

Go to  "Options" and select "user interface" then "manufacturer" from drop down menu.

[my smy sdna 200 died ?]

If it were me I'd open a ticket with Evolv and explain everything. It can't cost that much more to send three as opposed to one. Nothing to lose really, if they tell you to send them they most likely will take care of it. 
https://helpdesk.evolvapor.com/index.php?a=add

[my smy sdna 200 died ?]

I thought that was what you were saying.

[Preheat in Kanthal - It Works!]

It's in post #1 of this thread.

[tugboat dna200 does not work]

https://downloads.evolvapor.com/dna200.pdf
It shows it well here.
 

[tugboat dna200 does not work]

That's the way they do when the fuse is blown.

[Dna133/200 lower watt batt efficiency]

Perhaps your hitting the 6 volt ceiling. 6.2 volts on the 75 and  6 volts on the 133.

[After update 1.2 Sp3 device shows over Amp charging on vtbox200]

What battery did you get? I replaced mine with a 1300 mah ( https://www.hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=59112 ) had to shorten the main wires and change the plug. Turned out the original battery was good, got juice on the JST causing #3 cell to slowly drain when idle.

[my smy sdna 200 died ?]

I'm curious if Disley just means SMY mods or Evolv boards.

[After update 1.2 Sp3 device shows over Amp charging on vtbox200]

Still should be no higher than  0.5 amp either port (2 or 3) on any EScribe capable non Vapor Shark DNA mod. I don't know what VS charges with a data connection.
I guess the thing to do would be to try it with a different computer just to eliminate that.
Edit: Does it appear to actually charge extra fast?

[After update 1.2 Sp3 device shows over Amp charging on vtbox200]

On any non Vapor Shark 200 maximum amperage should be 0.5 amp with data path (computer) and 1 amp stand alone charger regardless of their respected output. The DNA 200 board controls charging. 
I'm curious if it's reading the correct amperage but suspect that it is.
Edit: but then again most (not all, eg. USB 3.0) computers only will output 0.5 amps.
Is there any possibility that there is juice on the bottom of the board around the USB?