dwcraig1
-
Posts
2,322 -
Joined
-
Last visited
-
Days Won
146
Content Type
Profiles
Forums
Downloads
Posts posted by dwcraig1
-
-
Here's my way of setting watt hours when using 18650's instead of 3S lipo pack, I use 87.5% of the rated mah.
My reasoning for this is the lipo packs get their mah rating from approx 3 - 4.2 volts while the 18650's are rated from 2.5 to 4.2 volts.
The calculator built into Escribe is meant for the lipo pack.
Just my way though. -
I had to look in Escribe.........twice...LOL
-
Isn't this a DNA75? I don't see these battery settings on my 75 like I do on my 133/200
-
Is this it?
"{0} can be used to analyze your atomizer's resistance stability."
or"Atomizer Analyzer"
-
I've not heard that for a 133dylang919 said:Someone said the 6 volt limit was going away. Any truth to that?
DNA75 max I believe is 6.2 volts -
If you get the cells balanced and put it into EScribe's device monitor and if the one cell is bad I think you will be able to see that as I suspect it will have extra sag compared to the other two cells.
-
This reminds me of when I got juice between the balance connector and the board but mine was a standard board.
-
0.41? to 0.46? is around 12.5%, it should have remembered it.
-
I think I'd be checking the mod's 510's connection to the the atty using atomizer analyzer, this sounds like maybe a poor connection between the mod's positive pin and the atty's positive pin. Or poor ground on the mod's 510. What mod is this?
-
Well it appears not to work, I can get it to only display 0's, thought a first it was full charged so I ran it down some and still 0's
-
Gee I had to look, it's there under the screen tab in the charging fields. It took a moment to switch from temp to current on the mods's screen but it works.
It does't show device monitor though only on the mod's screen. -
Cell #1 is really too low for a recovery charge, surely the battery is damaged.
A recovery charge will take many many hours, I see that you said that you tried that.
Contact seller or Vaporshark -
Scarab said:
Are you sure, you installed right EScribe version? (1.0.56)
I like this question......a lot. -
Try a different computer and/or a different cable. Get these things eliminated and let us know the results.
-
That 3rd cell reading is normal
I would set the soft cell to 2.9 volts and subtract about 10% from your watt hour calculation. (about 20 watt hours)
The 28.51 sounds like what 3 cells would be.
Why less watt hours? the battery was rated between 2.5 - 4.2 volts, you will be using 2.9 - 4.2 volts. -
Is there any possibility that there's e-liquid on the balance connections on the bottom of the board?
-
Just one example: the cable may be defective
-
A couple things besides something wrong with the board. Have you tried using a different cable? In EScribe, device monitor, diagnostics tab there is the ability to set, turn on/off charging...can you check that it is set to charge?
Also is battery set to LiPo and not power supply? -
-
Gee I thought I did this on my 75, I couldn't get it to work earlier today on my 75. I see I posted a live view of it a few posts back. Hmm
-
This is using a Vt133, single core 26 gauge Kanthal wrapped with 34 gauge Kanthal (dual coils) in Aromimizer v1.
![[13708413_1251475064876715_7632151450233204876_o]](https://scontent.fsan1-2.fna.fbcdn.net/t31.0-8/13708413_1251475064876715_7632151450233204876_o.jpg)
Firing at 70 watts, 110 preheat. -
OK give me a minute, I'd say that the temp is way out of whack though.
-
Credit and kudos to gorman
-
I certainly hope so, pick one that has a for real CDR of at least 20 amps.......or higher.
http://evolvapor.com/datasheet/dna75.pdf
Bad cell? What's your opinion?
in Batteries and Charging
Posted
Are you seeing sag like that in normal use?