dwcraig1
-
Posts
2,341 -
Joined
-
Last visited
-
Days Won
150
Content Type
Profiles
Forums
Downloads
Posts posted by dwcraig1
-
-
I'm running the latest and it's 1.1 - SP33.2
Must be a typo
-
It's quite possible that you might not have any problem inside them as they kind of seal. But since you have it out in front of you you might as well check them.
-
In the switch? once dissembled, clean out any liquid that may have gotten inside....either your e juice or the alcohol.
-
The screen sticks to the board. Be sure the screen comes with the board and not sticking in mod.
Carefully pry off the metal cover of the switch (red arrow). Try to bend it as little as possible, remove rubber piece, remove small metal disc.
Remove the screen prior to cleaning too.
https://downloads.evolvapor.com/dna250.pdf
-
The Lava box dna200 looks to have the typical set up for the buttons, a button on the face pushes against the button of the switch on the board.
-
I just finished one this morning that I got from the Ebay guy. It was a Hotcig DX200
Does the Lava box use a daughter board for the switches?
These are not clones, choose no battery, he will include one. He included two with mine.
-
So I finally locate VB's post showing the switch disassembled and the photo is gone.
-
Make sure to pay attention to which way the metal disc in the switches go, it is just one way.
-
1
-
-
No, it will want to eat things
-
2
-
-
I'm to understand that Lost Vape only works on one product at a time.
Here's one more:
https://vapordna.com/products/hcigar-vt75d-tc-dna-75c-box-mod
-
-
When you press the fire button once with it locked does the LED light up? If it does that would indicate that the button it's self is functional. To unlock requires 5 fairly quick presses.
-
The best place to get an answer to that is here:
https://helpdesk.evolvapor.com/index.php?a=add&category=1
-
I thought that SP38 solved that problem.
-
Use a magnifying glass if needed.
It goes into the slot marked by arrow, not above it.
Put it in squarely past the notch marked by arrow and carefully close cover.
I had major problems with this on my first one, I kept trying to put it between the door and connector instead of the slot.
-
1
-
1
-
-
In Escribe change the figure for battery capacity and upload settings. You didn't mention what cells that you are using so either convert mah to watt hours and subtract 20% or try a conservative figure like 25 wh if using 3 cells. Or run Battery Analyzer.
Note: I have modified the curve to reflect the change from max puffs to max recharges (charging stops at 4.1 volts)
-
EScribe 2.0 SP17 includes firmware SP35
-
40 minutes ago, vince159 said:
Hi Craig, long time no see. Yes, in fact, I am. I wasn't informed, didn't get a letter, post card or email
I'll look into it; Thanks very much Sir.
Suggest Int.
-
Are you using a version of EScribe that is one of the older versions that came out before the 250?
-
I'm surprised they didn't accept it.
-
Give it a try, pretty sure it will work out.
-
Might be an interesting read here:
-
If I were to guess I'd say the 510 ground connection is poor, for what ever reason.
Since it's new are you able to return it. If not open a ticket with Evolv and they will most likely take care of it for you.
https://helpdesk.evolvapor.com/index.php?a=add&category=1
-
If your not using this version of EScribe give it a try, this should do it.
https://downloads.evolvapor.com/SetupEScribe2_SP19_INT.pkg
Welcome to the forum
Left leaking tank on device overnight. Board temp spiked at 271deg. No fire.
in General Discussion
Posted
Don't wait for Evolv to reach out to you, you reach out to them here:
https://helpdesk.evolvapor.com/index.php?a=add&category=1