-
Posts
1,058 -
Joined
-
Last visited
-
Days Won
40
Content Type
Profiles
Forums
Downloads
Posts posted by giz_60
-
-
-
14 hours ago, oilaugust said:
You may have an issue with the Theme...can you post your theme? In Escribe, go to the Theme tab...click Save Theme & attach file here...
- 1
-
Y
1 hour ago, Critica1Err0r said:i just bought my 1st dna today. (Therion 166) i was hoping to change the way the device locks to pressing the + and - buttons at the same time. i really hate the 5x to lock
Uou can only change the number of fire clicks (down to 3x, IIRC) to lock the device
1 hour ago, Critica1Err0r said:should i load a profile for my HG2s?
This will only help the battery indicator, fuel gauge, to be more accurate
1 hour ago, Critica1Err0r said:possible firmware updates?
If a firmware update is available, Escribe will let you know and prompt to install
-
At only .01 - .02 rise in resistance from a cold coil to hot, it would seem that you are not getting enough of a rise in resistance. If the board doesn't see enough rise in resistance in the first second or so, it will drop out of TC. For instance, my current SS316L coil is .178 cold & rises to .210 - .211 after firing. Have you tried spacing your coils? What kind of atty? Can you post a screen shot of Device Monitor while firing, with the following fields checked...Power, Power Set, Temperature, Temperature Set, Cold Ohms & Live Ohms...
-
You can't use Ni200 material settings unless you are using the Ni200 coils...The info I previously posted was taken from Uwell's info on the Crown 3 coils & according to that info, the .25 & .5 ohm coils are better suited for wattage usage, not TC....
Edit:. Here is a response about a question of those coils found on another forum....
SS Coils on Uwell Crown have nickel legs, so they're to be used only on power mode because TC wouldn't read it correctly
-
14 hours ago, Omega1397 said:
Hey guys,
I've been having some issues using TC with my Crown 3 coils on my therion and paranormal 166.
I'm trying a profile I found by searching on the forums, that has the preheat power at 100W, temp at 530 F, and power at 80 W.
My issues are: On my .25 coil, my hits start hard, and then they get cool about 1.5 seconds in, and then I see the screen "Temperature protected", resulting in a short, unsatisfying vape.
For my 0.5 Ohm coil, the same thing happens but I get the error "ohms too high".
I was wondering if anyone could help me out. It would be very much appreciated!
According to the info provided by Uwell on their coils, it seems that the SS coils you are trying to use for TC are better suited for wattage & the Ni200 coils for TC....
Uwell crown replacement coils use revolutionary food grade stainless steel. Standard 0.25 and 0.5 coils are made of SUS316 D-Grade Stainless Steel Heating Wire and use 100% Japanese organic cotton. Temperature Control coils are made with 0.2 Ni200 Nickel wire.
0.15 ohm (Ni200 – Nickel)
0.25 ohm (80 – 120W)
0.5 ohm (30 – 80W)
- 1
-
In Escribe, go to the battery section of the Mod tab & make sure that it is set for 2 cell....restoring default in Escribe restores it to Evolvs default...3 cells...
-
Or...you could open a ticket with Evolv & let them guide you....https://helpdesk.evolvapor.com/index.php?a=add&category=1
-
25 minutes ago, omghax said:
Where can I find more of these? I specifically would just want the Samsung 25R, but don't know where to look...
Thanks
- 1
-
The .004 is NOT a live resistance reading, but rather what the Mod Resistance that is set at via Escribe...@retird was trying to get you to set it to 0 to show you that
-
You can also fill out a ticket with Evolv & let them guide you...https://helpdesk.evolvapor.com/index.php?a=add&category=1
-
Sounds like there is a connection problem between the board & the 510 connector...seems it is new, I would contact the seller about a warranty exchange...
-
If you have a Paranormal, there is a known issue with them. Read this post...it can also be causing the problem you are describing.....https://forum.evolvapor.com/topic/69140-paranormal-75c-resistance-too-high-fix/
-
-
-
One at a time...
-
There are a lot here...https://forum.evolvapor.com/files/category/6-dna-75-color-themes/
- 1
-
51 minutes ago, erix222 said:
How can i check for the bad connection with device monitor ?
By checking the voltage in Device Monitor with batteries installed individually...
- 2
-
Sounds like a bad connection on the battery sled...using Device Monitor in Escribe, you should be able to figure out which side it is on...
-
46 minutes ago, Mikescott said:49 minutes ago, Mikescott said:
can I connect the 75c mod usb cable to my samsung galaxy s7 edge ?
Regards Mike
No...Windows, Mac or Linux
-
Others have fixed issues with the Paranormal 166 this way...
-
If still in warranty, return to vendor....or contact Evolv & let them guide you....https://helpdesk.evolvapor.com/index.php?a=add&category=1
-
It was originally found when Dec. rolled around & the devices were rolling the yr. back to 2016 when connected to Device Monitor...https://forum.evolvapor.com/topic/69318-problem-with-date/
- 1
-
HCigar VT167 (DNA250 Board) Only Showing One Battery in Escribe
in General Discussion
Posted
Any voltage over 4.2x is a good indicator of a bad board/charging circuit.