Tj Roberts Posted June 4, 2019 Report Share Posted June 4, 2019 Does anyone know why this wire will not work in replay mode on my paranormal 250c the inner core is ss316l outer core is kanthal Link to comment Share on other sites More sharing options...
Tj Roberts Posted June 4, 2019 Author Report Share Posted June 4, 2019 Does anyone know why this wire will not work in replay mode on my paranormal 250c the inner core is ss316l outer core is kanthal Link to comment Share on other sites More sharing options...
jinx'd Posted June 4, 2019 Report Share Posted June 4, 2019 perhaps because the kanthal is what is "touching" the contacts ? idk, just say'n. but sounds reasonable. Link to comment Share on other sites More sharing options...
Wayneo Posted June 4, 2019 Report Share Posted June 4, 2019 Moderator Edit: Your duplicate posts were merged. Does the theme you're using support Replay? Is your mod in a Profile that supports Replay? Link to comment Share on other sites More sharing options...
Tj Roberts Posted June 4, 2019 Author Report Share Posted June 4, 2019 Yes Link to comment Share on other sites More sharing options...
Wayneo Posted June 4, 2019 Report Share Posted June 4, 2019 Follow from the 2nd paragraph in this post from @dwcraig. Up earlier in that post is how you can check, but if it's still not working ............. Post a printscreen of Device Monitor showing the live/cold ohm boxes ticked. Link to comment Share on other sites More sharing options...
Buckybuck Posted June 19, 2019 Report Share Posted June 19, 2019 I have the 26 36 all kanthal and my replay worked for about 10 puffs then stopped. I too would like to know why this is not working. I have restored themes and reloaded the stock config ... Still no option to save the puff (again after about 10 puffs of it working). I have the drone 250c if that matters. Link to comment Share on other sites More sharing options...
Tj Roberts Posted June 19, 2019 Author Report Share Posted June 19, 2019 Idk I still haven't figured it out Link to comment Share on other sites More sharing options...
dwcraig1 Posted June 19, 2019 Report Share Posted June 19, 2019 Replay will work with Kanthal or Nichrome coils only when there are numerous poor connections between the board and coil resulting in a resistance change due to voltage loss between the parts. Only TC wire is supported with Replay, Nichrome and Kanthal are not. 1 1 Link to comment Share on other sites More sharing options...
zark Posted June 19, 2019 Report Share Posted June 19, 2019 26 минут назад, dwcraig1 сказал: Воспроизведение будет работать с катушками Kanthal или Nichrome только тогда, когда между платой и катушкой имеется множество плохих соединений, что приводит к изменению сопротивления из-за потери напряжения между частями. Replay поддерживает только провод TC, а Nichrome и Kanthal - нет. Это абсолютно правильное мнение. Для того чтобы не продолжать дискуссию ни о чем, нужно понять, что Replay работает на принципах TC, по этому для проверки катушки попробуйте использовать её в режиме TC. Если катушка будет уверенно работать в TC, значит и режим Replay будет доступен. 1 Link to comment Share on other sites More sharing options...
EMARE Posted May 12, 2020 Report Share Posted May 12, 2020 (edited) @Tj Roberts, post an image of your atom build, how you connect the coils etc. Edited May 12, 2020 by EMARE Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now