Case thermals

[Guy Nicolson]

I have run case thermals for this mod and Escribe suggests this

It was left overnight to reach ambient temperature before running case thermals

Internal resistance has been measured @ 0.005Ω

New Turnigy nano-tech 2200mah 4S 25~50C Lipo Pack 

Any advice would be appreciated thanks

[retird]

Was the battery only half  charged before running Case Analyzer?  And you entered the real room temp before starting Analyzer?   

Wonder if you could run Analyzer again with the case door off of the device and see what it returns.........  

 

[Guy Nicolson]

Hello

   Battery was @ 25%

Temp reading taken from  a thermometer in the room with an out probe positioned  to give 2 readings 

Yes I will run it again with the door off 

Do you think it's the enclosure and lipo size?

[retird]

Unclear at this point....

[Guy Nicolson]

Ok I'll run it again

[Zaptear]

I get the same out of my n1 when I run the test 

[Zaptear]

Here is a pic

[Guy Nicolson]

Case thermals run again no door

50% charge 71.5℉

Turnigy nano-tech 2200mah 4S 25~50C Lipo Pack
Spec.
Capacity:2200mAh
Voltage: 4S1P / 4 Cell / 14.8V
Discharge: 25C Constant / 50C Burst
Weight: 218g (including wire, plug & case)
Dimensions: 100x35x30mm

Edited April 29, 2018 by Guy Nicolson

[Zaptear]

seems to cool faster with the door on that's weard 

[Guy Nicolson]

All tests have taken place in the same position in the same room 

I'm going to run it again with the door on at 50% charge  and see what I get this time

 

 

[Zaptear]

Running mine agen will post my stuff cell at 60% n1 so same box just I’m run a maxamp 4s 2800 100c 

[Zaptear]

[Zaptear]

 Ur my screen will not turn on after test kinda weard

[Guy Nicolson]

Bug?

[Zaptear]

I think so unplug from pc plug back in download settings kicks right back on 

[Zaptear]

I’m on the international firmware

[Guy Nicolson]

Good you are back 

Yes I'm on that version as well

[Zaptear]

But it dose do it every case test 

[Guy Nicolson]

No suggestion from Escribe about the mods case static temperature rise this time

It's been interesting  

 

[Zaptear]

Do thy even read this any more ?

[retird]

Yep, Evolv folks drop in and read..... at least two were here Saturday and/or Sunday........  and at least two this morning.... they are busy guys with many hats....  

So you have questions about the Case Static Temperature Rise right?  Both devices seem pretty consistent from your last run @ 18.4F and 18.25F

And does the device not turn on after the Case Analyzer finishes on both of you guys devices or only on @Zaptear device?

Anything else?

Question:    At what rate (current) does the device charge at when hooked up to your computers?  

[Zaptear]

I have to unplug and plug back into pc when don’t to get chip working agen it will fire just no screen but dose come back on after doing that and yes it will charge when pluged into pc

[Guy Nicolson]

 

My device turns on after Case Analysis 

I still do not know why the first Analysis gave those numbers, maybe the new lipo reaching proper balanced state as cell 3 was not in line with 1,2 and 4 at first, It was balance when I ran the first analysis though

1 amp from my Macbook

Nothing else thank you

 

Edited April 30, 2018 by Guy Nicolson

[Spector NS5 RD]

I would use the "with door om" test numbers, as that will be how you actually use the mod in real world scenarios.

I plan  on running Case Analyzer tonight myself. I will post screenshot results when finished.