Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 do you want a graph of my Drone 250 in temp mode with the same atomizer?. This was what i was expecting out of the DNA 75 Link to comment Share on other sites More sharing options...
giz_60 Posted April 29, 2017 Report Share Posted April 29, 2017 No, you said the Drone is working...need to figure out what you have set incorrectly on the BF Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 didn't even read temp that time Link to comment Share on other sites More sharing options...
giz_60 Posted April 29, 2017 Report Share Posted April 29, 2017 Better, thanks...now let's see Profile 1 in the General tab Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 Link to comment Share on other sites More sharing options...
giz_60 Posted April 29, 2017 Report Share Posted April 29, 2017 If you look at the last Device Monitor screen shot, the cold ohms are holding steady at .59...when you fired, they dropped & then leveled off at .601...you have a fluctuating resistance issue...if that atty is working good on the Drone, then you may have gotten some juice into the 510 connector on the BF. that is a common problem with BF devices...try cleaning it with some iso alcohol... Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 lol..no bottle connected...everything cleaned..spent over 29 hours on this mod.. I think I have a defective DNA 75 chip Link to comment Share on other sites More sharing options...
retird Posted April 29, 2017 Report Share Posted April 29, 2017 And I might add..... in Profile 1 the coil material is set to SS316L... check that drop down list and see if there is another SS316L to choose. If so, select it and see if that helps... Your post #4 shows 2 SS316L materials installed on the device... Link to comment Share on other sites More sharing options...
giz_60 Posted April 29, 2017 Report Share Posted April 29, 2017 retird said:And I might add..... in Profile 1 the coil material is set to SS316L... check that drop down list and see if there is another SS316L to choose. If so, select it and see if that helps... Your post #4 shows 2 SS316L materials installed on the device...And 1 of them has the wire profile for NI200 associated with it Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 i haven loaded 4 316L profiles..nope Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 here is how it is supposed to work..DNA 250 in Lost Vape Drone Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 I will do us all a favour and destroy this DNA 75 so no one has the same problem as me Link to comment Share on other sites More sharing options...
retird Posted April 29, 2017 Report Share Posted April 29, 2017 giz... I'm backing out as he is confused with more than one trying to help... I think his material SS316L he is using actually is for Ni200... he has 2 materials named SS316L so choose the other one... good luck... Link to comment Share on other sites More sharing options...
Spirometry Posted April 29, 2017 Report Share Posted April 29, 2017 Little Brat said:i haven loaded 4 316L profiles..nope You also have one NI200 profile named SS316L. Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 I have run out of patience tonight.. I appreciate your help.. I will try again in the morning Link to comment Share on other sites More sharing options...
Wayneo Posted April 29, 2017 Report Share Posted April 29, 2017 Clearly the wrong wire profile. That ending value at 800F should be close to a value of 1.33 (off the top of my head).Easy fix @Little Brat. I'll let giz finish up. Link to comment Share on other sites More sharing options...
giz_60 Posted April 29, 2017 Report Share Posted April 29, 2017 Some how, some way, you have gotten the wire profiles wonky on your device. If you had down loaded & loaded, into your device, the SS316L .csv from Steam Engine, it would be named "SS316L Elite" in the materials tab. So, you need to start from scratch.1. In the General tab, on Profile 1, change the 'Coil Material' to anything BUT SS316L...Scroll through the rest of your Profiles to make sure SS316L is not assigned to any. If so, change them too.2. In the Materials tab, delete everything that says SS316L (both in the 'Available Materials' box & 'Materials on Device' box)3. Re-load the Steam Engine .csv & move it over to the device. (should be named SS316L Elite)4. General tab...change the Coil Material to SS316L Elite5. Upload to deviceHere is the SS316L .csv from Steam Engine in case you need it.... DNA200-SS_316L _Elite-SteamEngine.csv 129 Bytes 0 downloads (It doesn't matter that it says..."DNA200" in the file name)DNA200-UD-SS_316L_DJaquith_V4.csv Link to comment Share on other sites More sharing options...
Wayneo Posted April 29, 2017 Report Share Posted April 29, 2017 Hey @Little Brat, might I suggest you only do as asked, and not venture off doing your own thing as it makes things more difficult. You're screenshots are our eyes, and our requests ... your fingers. Here's an example. In your post #3, look at your wattages and 'ohms lock'[QUOTE=Little Brat] [/QUOTE]Then when requested a second time, you actually made changes (Post 31), albeit only a 2.5 watt decrease, but now the ohms are locked. A change, perhaps to preserve and retain the value, if in between was when you did the drone screenshot[QUOTE=Little Brat] [/QUOTE]You'll be all fixed up relatively quickly my good man. The DNA's can seem quite daunting at times. In the hands of anyone that commented here, I'd say less than 10 minutes. Others working as our fingers adds time naturally. Have a good night. Link to comment Share on other sites More sharing options...
Egraypgh Posted April 29, 2017 Report Share Posted April 29, 2017 My thereon came preloaded with only the ni200 curve. The other materials were all set up with ni200 curve simple fix delete the SS and Ti curves and download them from steam engine. It looks like you have already added a second 316l but are probably still selecting the ni200 curve labeled ss316. i suspect that following giz_60's suggestion above will get you where you need to be. Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 thx..it is working. I thought I deleted every SS 316 CSV file but I guess I didn't Link to comment Share on other sites More sharing options...
giz_60 Posted April 29, 2017 Report Share Posted April 29, 2017 Awesome...glad to hear ya got it working... Link to comment Share on other sites More sharing options...
giz_60 Posted April 29, 2017 Report Share Posted April 29, 2017 On a side note...have you run the case analyzer yet? Having the proper Case Thermal values is quite important when vaping in TC mode. At the bottom of the Mod tab, if your Case Thermal values look like the following screenshot, then you have the defaults..highly recommend running the case analyzer...will take awhile (couple of hours or so)...make sure your batteries are at least 50% drained prior to running the analyzer....and I would leave the computer alone while it's running because if for some reason the connection to the USB port is disrupted, it stop & you will have to start again..take it from experience... Link to comment Share on other sites More sharing options...
Wayneo Posted April 29, 2017 Report Share Posted April 29, 2017 On another side note... Do you still have that 'resistance locked' in the profile? It stops the board from working half its magic, and IMHO mainly effective for shoddy builds with jumpy ohmsRefinement - DNA 75 Datasheet, Page 6, under 'Resistance lock' Link to comment Share on other sites More sharing options...
Little Brat Posted April 29, 2017 Author Report Share Posted April 29, 2017 thx.. i did run the case analyzer but I guess it didn't save the settings Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now