dwcraig1 Posted January 21, 2019 Report Share Posted January 21, 2019 EScribe shows the two cells around 4.135 volts when charging stops. It is set foe maximum puffs. If I check the cells with a volt meter they read 4.2 volts. Does anyone else have this problem? Link to comment Share on other sites More sharing options...
dwcraig1 Posted January 23, 2019 Author Report Share Posted January 23, 2019 I figure that I should set this straight, the readings from my volt meter were wonky, I measured again with my other meter and the readings between what EScribe was reporting and the meter were the same. Link to comment Share on other sites More sharing options...
Vapors Tongue Posted April 8, 2019 Report Share Posted April 8, 2019 Just got a VTbox but not experiencing any problems Link to comment Share on other sites More sharing options...
dwcraig1 Posted April 9, 2019 Author Report Share Posted April 9, 2019 Mine leaked badly from the 510 after about a week as many other users had reported. Link to comment Share on other sites More sharing options...
Vapors Tongue Posted April 9, 2019 Report Share Posted April 9, 2019 juice was going down the 510 ? did you see what was going on and fix it or send it back - i hope i dont experience anything like that i really like this box Link to comment Share on other sites More sharing options...
Vapors Tongue Posted April 9, 2019 Report Share Posted April 9, 2019 ahh the VTX is a squonker - just been having a look i'm sure you posted a pic of it in the group didn't you change the board in it or is that one that looked similar Link to comment Share on other sites More sharing options...
dwcraig1 Posted April 9, 2019 Author Report Share Posted April 9, 2019 Yes I removed the board and put it in an SXK Boxer squonk. I then checked out the problem with the VTX's 510, the o-ring they used was too small. Link to comment Share on other sites More sharing options...
Vapors Tongue Posted April 9, 2019 Report Share Posted April 9, 2019 3 minutes ago, dwcraig1 said: Yes I removed the board and put it in an SXK Boxer squonk. I then checked out the problem with the VTX's 510, the o-ring they used was too small. Crazy , do these people test these device , its like the Drone Squonker why make a door so flimsy when that's the main area its going to get most usage but i like the mod very much but with the ultem you certainly have to watch out about that door area on squeeze to hard and if the door isnt aligned or slightly out something then its going to break Link to comment Share on other sites More sharing options...
Podunk Steam Posted December 10, 2019 Report Share Posted December 10, 2019 On 4/9/2019 at 1:26 AM, dwcraig1 said: Yes I removed the board and put it in an SXK Boxer squonk. I then checked out the problem with the VTX's 510, the o-ring they used was too small. I've pulled my SXK Boxer apart for a quick look at a DNA75c transplant and found the 510 just isn't looking so straight forward on brief inspection. Any pointers on pulling the 510 apart without thrashing it? Link to comment Share on other sites More sharing options...
Podunk Steam Posted December 10, 2019 Report Share Posted December 10, 2019 (edited) Thank you cdwraig1! Your picture and directions are much appreciated although I don't see your post here? It all shows in my email browser but not here on the forum. I've just pulled the mod apart again and may be able to avoid pulling the 510 apart. I'm guessing the 250C is a better fit than the 75C, the circuit board has plenty of wiggle room with the 75C. Quote dwcraig1 said: Remove the positive wire making sure to remove as much solder as possible. I used flush cutters to remove the wire from the tube. Remove the cir clip and it comes apart. When soldering the wire back on extend the tube as far as possible and heat sink the tube by holding it with nettle nosed piers so the heat doesn't damage the insulator and o-ring, Edited December 10, 2019 by Podunk Steam Link to comment Share on other sites More sharing options...
dwcraig1 Posted December 10, 2019 Author Report Share Posted December 10, 2019 The reason that I deleted my post was because it was for the Vapecige box not the SXK Boxer. On the SXK I believe that the offset piece screws onto the 510 pin but am not sure. 1 Link to comment Share on other sites More sharing options...
Podunk Steam Posted December 11, 2019 Report Share Posted December 11, 2019 2 hours ago, dwcraig1 said: The reason that I deleted my post was because it was for the Vapecige box not the SXK Boxer. On the SXK I believe that the offset piece screws onto the 510 pin but am not sure. Good man! All's well, paralleled it's really tight but she fit. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now