iambyrdman Posted April 17, 2018 Report Share Posted April 17, 2018 I just finished my build and had replay working. At some point messing with stuff I've turned it off and can't figure out how to get it back. Strange... Link to comment Share on other sites More sharing options...
iambyrdman Posted April 17, 2018 Author Report Share Posted April 17, 2018 Anybody know what I did? Link to comment Share on other sites More sharing options...
retird Posted April 17, 2018 Report Share Posted April 17, 2018 What "stuff" did you mess with? Is "Support Replay on this profile" still checked? Link to comment Share on other sites More sharing options...
iambyrdman Posted April 17, 2018 Author Report Share Posted April 17, 2018 2 minutes ago, retird said: What "stuff" did you mess with? Is "Support Replay on this profile" still checked? I was only changing things like step down size. I HATE 10th of a watt of 5 degrees at a time. Support Replay is checked on all temp coils and Replay profile. What is, "Saved Puff, Playing." I've tried it with and without. I've also UNlocked resistance on all. Link to comment Share on other sites More sharing options...
iambyrdman Posted April 17, 2018 Author Report Share Posted April 17, 2018 I went into EScribe and ask for Ohms for every profile and now it's working again. Link to comment Share on other sites More sharing options...
retird Posted April 17, 2018 Report Share Posted April 17, 2018 Yep, The board needs to know the ohm's of the atty/coil..... good that you got Replay going.... if you look in EScribe now the "Saved Puff, Playing" is checked.... Link to comment Share on other sites More sharing options...
iambyrdman Posted April 17, 2018 Author Report Share Posted April 17, 2018 (edited) Now it has stopped working again. I get the feeling it's because I've been using a Kanthal coil at times. Replay is not available after using Kanthal it seems. I've even gone to the profile for the coil type before going to replay profile. I'm using the Paranormal Red profile and the word, "Available" is there instead of replay Edited April 17, 2018 by iambyrdman Link to comment Share on other sites More sharing options...
iambyrdman Posted April 18, 2018 Author Report Share Posted April 18, 2018 I've tried Restoring Defaults and default unaltered theme and can't get it back now! So frustrating. Why is this so difficult? It shouldn't be! Link to comment Share on other sites More sharing options...
cs1981 Posted April 18, 2018 Report Share Posted April 18, 2018 here are the factory settings from lost vape. try to load them. I did the same thing, and got it working after loading this file to the dna chip. Paranormal DNA250C-settings profile.ecig 1 Link to comment Share on other sites More sharing options...
iambyrdman Posted April 18, 2018 Author Report Share Posted April 18, 2018 Didn't work. I'm wondering if it's a physical install problem at this point. I'd send it to Evolv but they have not replied to 2 RMA requests!!! Link to comment Share on other sites More sharing options...
Nick Posted April 18, 2018 Report Share Posted April 18, 2018 2 hours ago, iambyrdman said: Didn't work. I'm wondering if it's a physical install problem at this point. I'd send it to Evolv but they have not replied to 2 RMA requests!!! My apologies. I don't see any tickets in our system recently, how are you trying to contact us? Get a ticket in here and we would be happy help. https://helpdesk.evolvapor.com/?a=add Link to comment Share on other sites More sharing options...
iambyrdman Posted April 18, 2018 Author Report Share Posted April 18, 2018 (edited) 6 hours ago, Nick said: My apologies. I don't see any tickets in our system recently, how are you trying to contact us? Get a ticket in here and we would be happy help. https://helpdesk.evolvapor.com/?a=add Hey Nick it's Winston. Let me know when you get back to eating pizza and I will totally come see you! I'm pretty sure what's how I did it before but I just did it again. "Your ticket has been successfully submitted! Ticket ID: EZX-GJX-4X3X" Edited April 18, 2018 by iambyrdman Link to comment Share on other sites More sharing options...
rask116 Posted April 20, 2018 Report Share Posted April 20, 2018 (edited) Only reply I have is... Welp I lost my replay too. Yes it was working great before............ I went into theme designer and changed the .1 increments to 5 and changed the background to the hump mountain bg that came with escribe, Didn't think I did anything else though. After getting frustrated, I came here, found this thread, saw the paranormal 250c link, so tried that. Nope didn't work, so tried to restore defaults. Nope that was a no go too,...so really got adventurous and whet to the themes here to try one of them, to see if maybe one of them would somehow help. Nope. so went back to default and basically all I have is a 2 day old Think Vape Finder 250c with no replay, Great! Not! I own 7 dna devices 4 diy ( 2x 200 and 2x250) and 3 china manufactured ones, 2 of them are 200s and the other a 250 and now this 250c. I had thought I'd be pretty salty in escribe with this one , but have learned that I know nothing now. HELP! Everything here in this thread so far offered as advice hasn't. worked for me. I'm very lost now,, ps: I downloaded the international version of escribe and installed it before I ever plugged the device into my computer . I saw no where in escribe to "ask for ohms for every profile". Well no where under the general tab or on each profile page I didn't see it, Edited April 20, 2018 by rask116 Link to comment Share on other sites More sharing options...
rask116 Posted April 20, 2018 Report Share Posted April 20, 2018 (edited) I also submitted a ticket, hoping to get some help that way too. Ticket ID: WQD-EP2-Y9XT Edited April 20, 2018 by rask116 Link to comment Share on other sites More sharing options...
vapingcrusty Posted April 30, 2018 Report Share Posted April 30, 2018 Same here. it worked out the box after ticking the boxes for allow replay and puff saved playing also allow dubious coils. it started to play up a bit but sometimes worked. Now it won't work and everytime i go into escribe the save puff playing box is unticked for ss316. I also put the old escribe on to put replay on my DNA75c and had no luck at all with that the replay has never worked , yes i put the sp's on both had the sp 33.2 installed so i must be doing something wrong, i tried reloading the paranormal file and restoring defaults. to say i am peeved is about right as i own 15 DNA devices and never had an issue with the old boards. I will dig out my ols atlantis tank and stick a ni200 coil in to see if it is ss316, 316l causing the problem. Link to comment Share on other sites More sharing options...
GHammer Posted May 1, 2018 Report Share Posted May 1, 2018 I had Replay 'working' in TC mode. Then, I was informed that Replay was meant for wattage users and would work best in that mode. Setting my profile to 'Watts' didn't produce any vapor, just the Check Atomizer warning. After a bit, I decided to try a different method to get Replay working as intended. I use SS430, so was using that as my material. When I did that, the mod was somewhat confused. I saw Temp instead of volts on the display and could only change Temp from the main display, no wattage. I think it worked, but as TC is solid I couldn't really tell. Anyway, I changed my settings. On the mod tab, I chose Allow dubious coils and unchecked Support only temperature-sensing coils. Then I set up a profile to use Replay in power/wattage mode. And, it works a treat. I have wattage displayed for change, and see volts instead of temp. Plus, it works as shown by device monitor. No temp displayed there now. Link to comment Share on other sites More sharing options...
vapingcrusty Posted May 1, 2018 Report Share Posted May 1, 2018 Ok it must be wire or wicking. I just dug out a titanium coil stuck it in a freemax starre and now replay is working. fine on the Paranormal. I will now try and get the 75c working. 316l seems to be the problem both in temp or wattsge modes Link to comment Share on other sites More sharing options...
Zak2017 Posted May 2, 2018 Report Share Posted May 2, 2018 (edited) I am facing the same problem. I have paranormal 250c. As soon as I got it, I downloaded the international version and saved the default settings in case I mess up something. I set up 2 titanium profiles. One was temp control and the other was Replay. It worked fine for a day and a half. Then: On 4/20/2018 at 2:36 AM, rask116 said: I went into theme designer and changed the .1 increments to 5 and changed the background to the hump mountain bg that came with escribe, Didn't think I did anything else though. I did same thing @rask116 did ^ After uploading settings, my 2nd titanium profile (the replay enabled) was different. I no longer have the replay option there. Now, looking at the mod, there isn't a difference between my 2 titanium profiles. They both show wattage and temperature. No option to "save". I checked my profiles on escribe. Everything was in order. Same as @iambyrdman On 4/17/2018 at 10:02 AM, iambyrdman said: Support Replay is checked on all temp coils and Replay profile. I unchecked the replay options and rechecked them. Uploaded settings without any luck. I then downloaded the original settings I saved earlier before making any change, but still no replay option for my 2nd titanium profile. Has anyone found a way to solve this mystery? Any ideas @Nick Edited May 2, 2018 by Zak2017 Link to comment Share on other sites More sharing options...
iambyrdman Posted May 2, 2018 Author Report Share Posted May 2, 2018 8 hours ago, Zak2017 said: Has anyone found a way to solve this mystery? Any ideas @Nick From what I've found, your coil has to very VERY stable. Other than that I think you did the right thing going back to default. I'd keep it that way until you figure it out, them tweak. Link to comment Share on other sites More sharing options...
rask116 Posted May 2, 2018 Report Share Posted May 2, 2018 (edited) I got this reply from a ticket from the help desk which stated: "Connect the device to EScribe and from the top dropdowns try Edit > Timeline and see if it will let you go back to before it was changed." I ended up, however, trying a few other themes from the download section and found one that worked. "gauges". The only downside to this theme is that it is incredibly hard, if not impossible, to see while outside or in a vehicle. But it got me back to having the replay on all profiles. BTW, replay works in temp mode as it was designed to do originally, only later, after some software updates, did replay start working in watt mode or Kanthal. It wasn't originally meant to work in wattage or non-temp sensing wire. But it works on all vape wire now. Just make sure you have a good material .csv profile from wire wizard ( mind you that wire wizards profiles are for dna 200 chips, so some tweaking will need to be done with the .csv files for the 250c. IE: I use nothing but 317L ss wire and had to play around with the .csv file for a while to get it acting right with the dna 250c. worked without flaw on the 200 and 250 but it wasn't acting right with the 250 c. Probably due to the chip being able to do 300watts which of course change the temp ranges even if you don't ever go or use 300, 200 watts)) Edited May 2, 2018 by rask116 Link to comment Share on other sites More sharing options...
rask116 Posted May 2, 2018 Report Share Posted May 2, 2018 (edited) Correction to above post I typed: "Probably due to the chip being able to do 300watts" which should have read: Probably due to the chip being able to do 400 watts total which of course, changes the temp ranges even if you don't ever go to or use 400, 300, 200 watts Edited May 2, 2018 by rask116 Link to comment Share on other sites More sharing options...
mrdidit Posted May 4, 2018 Report Share Posted May 4, 2018 The same thing happened with me. Have got the device today. Latest(only?) int firmware installed. Replay was working. Before even having my hands on the device, already have downloaded a replacement Theme, Material-ish Fire - DNA75c - DNA250c Optimized 1.1.0 Installed the mentioned Theme, but didn't like it so in EScribe I clicked on default Theme. Since then, Replay stopped working. I tried to find the Default Theme, without luck. So I tried to upload the mentioned Theme again. Voilà, Replay is working again. So I believe, the Default Theme included in EScribe has an older Theme, doesn't support Replay. Of course, I'm not 100% sure. Cheers, Hope it helps Link to comment Share on other sites More sharing options...
JurgenDP Posted December 8, 2018 Report Share Posted December 8, 2018 I have a problem with my Paranormal 250c my Replay on kanthal coils (cleito 120 and the aspire pro) worked, but very difficult, I really have to pull them warm and then the puff pastry appears. It is better not to make suggestions Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now