ikicho Posted October 24, 2017 Report Share Posted October 24, 2017 Hi, Im having a problem with the combo of therion 166 and kylin rta. Always the first pulse is constant but the one that follows i feel like the output of power is delivered as pulses. Any idea? Link to comment Share on other sites More sharing options...
Wayneo Posted October 25, 2017 Report Share Posted October 25, 2017 (edited) Hey man, can I see that again, but this time after your first, just set the mod down, See puffs over on the right, choose 4 seconds and let your mod do it. Stop the scrolling, move the mouse over the lowest area (deepest valley before another rise) and a printscreen of that. Can you describe your coil? I have only experienced that in 3 scenarios. Inconsistent inhale, or an overpowered set of parameters for a low mass single wire build or uneven coils Edited October 25, 2017 by Wayneo 1 Link to comment Share on other sites More sharing options...
ikicho Posted October 25, 2017 Author Report Share Posted October 25, 2017 (edited) Hi wayneo. Its a dual 3.5 ID 6 wraps dual coil of stagger fused (26ga+32ga)*2+32ga made from a spool of geekvape. On atomizer analyzer it show 0.135 ohms steady with no variations and in device monitor the cold resistance its 0.128 im using a profile made from wire wizard with all the characteristics as said In the graph the numbers are overlaped but the lowest point of power i think its 1.65W By the way i have a ijoy rdta 5 made with the same wire, but not same id and wraps and the puff its steady I´ve tryed the djaqith v3.5 profile with the same results, first puff is steady the following ones are pulse Sry for potato english not my native lenguage thx for the help Edited October 25, 2017 by ikicho more information Link to comment Share on other sites More sharing options...
Wayneo Posted October 25, 2017 Report Share Posted October 25, 2017 Good English. I really think this is a build issue, as your other atty/build works fine. Can you check there are no hotspots, if a contact coil, try a spaced one. Link to comment Share on other sites More sharing options...
ikicho Posted October 25, 2017 Author Report Share Posted October 25, 2017 I have already checked if there is any hot spot, just now im wicking it again and no hot spots, will try if the pulsing is still there and report. In the other atty its also contact coil and no problems but if the problem is persist in the kylin i will try. Thx Link to comment Share on other sites More sharing options...
awsum140 Posted October 25, 2017 Report Share Posted October 25, 2017 Just in case, check/clean the center screw in the 510. I've had some strange things happen when they get dirty. It doesn't take much to make TC not work well. 2 Link to comment Share on other sites More sharing options...
ikicho Posted October 29, 2017 Author Report Share Posted October 29, 2017 Ive always keep the 510 clean, and the problem continued. Yesterday i rewiked it and noticed a really small hot spots, i think that in fancy coils its hard to work out hot spot or even visualize them, so i spaced a little bit and it has been working great! Ive the give the reason to Wayneo. From now one i will keep all my coils for tc a little spaced Thanks you both! Link to comment Share on other sites More sharing options...
Wayneo Posted October 29, 2017 Report Share Posted October 29, 2017 Glad you got it working. I have had contact coils also work, but as we suggested, it's usually a cleanliness, build or connection issue. Cheers 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now