InvisibleRasta Posted October 10, 2017 Report Share Posted October 10, 2017 (edited) hello guys i just updated my firmware with excribe to the latest sp 1.5 i think it was. When i try to use TC for SS316L i cant find a profile. the steps i am using to try to select the SS3162L profile are these that i wrote in red at the bottom. But it gives me only profiles for nickel. Escribe software does not have any preset and i do not know where or how to setup a SS3162l profile lock the DNA device with 5 clicks, once it is locked hold down booth, plus, minus and fire button and select the material you want to use to vape with temperature control. Edited October 10, 2017 by InvisibleRasta Link to comment Share on other sites More sharing options...
Wayneo Posted October 10, 2017 Report Share Posted October 10, 2017 The latest firmware and escribe is found here: Go to the 'material' tab to see what wire types are available, and on your mod. Your RED comment works in newer versions. Latest tells us nothing, but you can see it in the bottom right hand corner of Device Monitor. 1 Link to comment Share on other sites More sharing options...
InvisibleRasta Posted October 10, 2017 Author Report Share Posted October 10, 2017 (edited) i restored defaults and i am on the latest firmware... my build is spaced 24 gauge SS316L with 7 wraps on a 3mm drill bit. I selected the SS316 profile as described on my red comment and put the temperature to 130 Celsius but it fires vapour like lava... like if it was on power mode at 200 Watts... Teh Watts output with TC enabled is at max power that i set at.. Watts dont change according to temps... liek i set watts to 50W and it will fire 50W all time TC not working Edited October 10, 2017 by InvisibleRasta Link to comment Share on other sites More sharing options...
Wayneo Posted October 10, 2017 Report Share Posted October 10, 2017 Escribe - Material tab. Highlight the wire you chose on the right hand side. Look down at graph/line. Tell me what values do you see at the highest setting? Follow my instructions here and do a Printscreen exactly like he did. 1 Link to comment Share on other sites More sharing options...
InvisibleRasta Posted October 10, 2017 Author Report Share Posted October 10, 2017 (edited) i do not fully understand your instructions. I opened device monitor,fired and took a screenshot i tried to set at 150C but when i fire it shows it goes up to like 1300C.... thats like about to blow up the wire Is there Edited October 10, 2017 by InvisibleRasta Link to comment Share on other sites More sharing options...
InvisibleRasta Posted October 10, 2017 Author Report Share Posted October 10, 2017 one time it fires like lava... without changing anything other time it fires and says temperature protected but no vapour comes out Link to comment Share on other sites More sharing options...
Wayneo Posted October 10, 2017 Report Share Posted October 10, 2017 For not understanding, you done great. Can you do a Printscreen of 'Profile 1', please. And tell me what kind of batteries you're using? At a bare minimum, on the 'mod' tab, double the value for Wh's. 1 Link to comment Share on other sites More sharing options...
InvisibleRasta Posted October 10, 2017 Author Report Share Posted October 10, 2017 (edited) i just did a default settings restore so i have the default factory profiles.... from my understanding they are all set to nothing... im using 3 efest batteries... they are pretty old also with the update the power only profile disappeared.. and now im vaping a kanthal build on the NI profile as there is no power profile Edited October 10, 2017 by InvisibleRasta Link to comment Share on other sites More sharing options...
Wayneo Posted October 10, 2017 Report Share Posted October 10, 2017 (edited) If you don't connect a wire capable of TC, it will fire at the wattage selected. If you do connect a wire capable of TC, it will fire using the material profile selected, in the screenshot 'ni200'. So you're vaping kanthal @ 37.4watts. If you're gonna keep changing things/resetting things I'm not asking you to do, I'll go cut the lawn. Edited October 10, 2017 by Wayneo Added a word 1 Link to comment Share on other sites More sharing options...
Wayneo Posted October 10, 2017 Report Share Posted October 10, 2017 On your 'material' tab, left side, see the one called 'watts', click to highlight, then that right arrow -> in between the two windows to put it back on your mod. You should still have SS316 in the right window. If not, do the same thing as before for 'watts' 1 Link to comment Share on other sites More sharing options...
InvisibleRasta Posted October 10, 2017 Author Report Share Posted October 10, 2017 (edited) i did not do anything.. everything is as after i did a firmware update, without profiles. but after i did the restore defaults i didnt have a watts option available.. so now i wanted to vape with my rda since my RTA with SS316 is firing lava. I now have the watts option back, thank you for the information. Back to the ss316 problem, what can i do? Edited October 10, 2017 by InvisibleRasta Link to comment Share on other sites More sharing options...
Wayneo Posted October 10, 2017 Report Share Posted October 10, 2017 Check your watts material in the right hand window. Make sure 'temperature sensing' is not selected below it, just above the graph. Set a profile, I usually set Profile 1 back to your watts material Go to Profile 2. Put Power at 100 watts, temp of your choice (150C) is fine. Click on temperature dominant. Do not lock resistance. Leave the other defaults for now alone. Near top of screen -> Upload settings to device (always gotta do this) Atty should be at room temperature, wicked and ready to go. Device Monitor. Bottom left side should say Normal or charging. Over to the right it should say Profile. Click on that, change it to Profile 2 Put mod down on table. Device Monitor, far right, see Puffs, click and set to 3 seconds. Your mod will fire, and no lava for you. Post printscreen like the second one you did before. 1 Link to comment Share on other sites More sharing options...
Wayneo Posted October 10, 2017 Report Share Posted October 10, 2017 Or ya can send me a printscreen of profile 2, and device monitor when you're all set to fire. 1 Link to comment Share on other sites More sharing options...
InvisibleRasta Posted October 11, 2017 Author Report Share Posted October 11, 2017 this are the results.... still fires quite lavaish...sometimes at 150C it will fire lava... some other times it will fire godod... with same options profile and whats so ever...without touching anything...super unstable Link to comment Share on other sites More sharing options...
Wayneo Posted October 11, 2017 Report Share Posted October 11, 2017 8 minutes ago, InvisibleRasta said: still fires quite lavaish...sometimes at 150C it will fire lava... some other times it will fire godod... Rasta, overall that looks good. Couple comments. The only ways I can see you getting lava is if it's firing 100 watts straight (non TC) OR the wrong wire profile. If you don't plan on using Nickel or Titanium in the near future, go into profiles and change them to SS. Then go to Material tab, right window, select, then remove from mod. Preheat should be greater than the Power number. Yours show both at 100w. 100watts, is clearly too much to maintain the watts required, so you can drop the Power to 50w, leaving preheat at 100 if you wish (if you liked that ramp up) You can tweak any of those 5 values to your desire. Note that even though we said 100w, your temp was ~150c. Always remember to upload settings to Device after you make changes in escribe Under File -> Save As you can save a backup of all your settings. 2 Link to comment Share on other sites More sharing options...
InvisibleRasta Posted October 18, 2017 Author Report Share Posted October 18, 2017 (edited) seems like its working now... only thing is how do i switch profiles from watts to 316 profile? really this chip with each update has become more and more hard to use.. i do not understand anything of it anymore... it used to be easy to select watt profile or 316 profile... now i had watts enabled for my rdta.. i want to switch to TC... i select preset 316 and boom... firing at full power... cotton burnt in a second Edited October 18, 2017 by InvisibleRasta Link to comment Share on other sites More sharing options...
Wayneo Posted October 18, 2017 Report Share Posted October 18, 2017 13 minutes ago, InvisibleRasta said: only thing is how do i switch profiles from watts to 316 profile Rasta, there are 2 different ways. Your RED text above allows you to change materials 'on the fly' and follow the preheat, punch, time, watts set for it right now. Used if you want a soft, medium, hard type settings. To change to a new profile completely (like your 316 profile); hold up and down button at the same time till screen displays message quick double click either button (displays current profile name) click either up or down button to change to next complete profile click fire button once you reach the profile you want hold up and down button at the same time till screen displays message 27 minutes ago, InvisibleRasta said: i select preset 316 and boom... firing at full power... cotton burnt in a second If you followed your red text that can happen. 1 Link to comment Share on other sites More sharing options...
InvisibleRasta Posted October 18, 2017 Author Report Share Posted October 18, 2017 with the older update i had djlsbvapes profiles loaded and it was so much easier to understand and change things. but on his site now he says not to use these profiles Link to comment Share on other sites More sharing options...
Wayneo Posted October 18, 2017 Report Share Posted October 18, 2017 I've seen some of his where they were named like soft, medium, hard, no preheat, etc. If you liked/used those (which are still perfectly fine), then with your red text, you end up choosing the type of profile and change material only. OR You set up specific profiles based on material/wire, and use that for a complete setup. Personally, I use a combination of each on a mod where it's painful to get escribe access. 1 Link to comment Share on other sites More sharing options...
InvisibleRasta Posted October 20, 2017 Author Report Share Posted October 20, 2017 thank you Wayneo for helping me setting up my dna200. I finally can vape my SS and claptons properly... as of now i havent seen any weird things happening. thank you again 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now