LeviAsHimself Posted July 31, 2016 Author Report Share Posted July 31, 2016 My sdna75s screen has been acting up for a few days now. It would flash and freak out when I fired it or tried to take it out of stealth mode, then today it just went out completely, the mod works fine but the screen won't turn on at all. So far I have tried updating it and hard/soft rebooting it, at this point I'm not sure what it could be. Link to comment Share on other sites More sharing options...
VapingBad Posted July 31, 2016 Report Share Posted July 31, 2016 Could be the screen cable has worked loose or got pinched and damaged by fire button. In ESccribe - Help - About click the logo 7 times then open Device Monitor and you will see a filed "Screen Disconnect" and if this is more than zero if is likely what I suggested. I don't have that mod so can't say who easy it is to get to the cable to chech. Link to comment Share on other sites More sharing options...
LeviAsHimself Posted August 3, 2016 Author Report Share Posted August 3, 2016 Thank you for the quick reply, sorry it took me so long i was away for a few days. the number is around 750 so i will tear the mod apart and take a look at the wires later on tonight, again thank you. Link to comment Share on other sites More sharing options...
crazyD Posted September 7, 2016 Report Share Posted September 7, 2016 I'm assuming the screen disconnect number is a rolling count .... I began having problems with one of my DIY's - and when I did what you described above ... the number was 133. then when I hit the fire button it jumped to 141 - but I only hit the button once, so maybe I'm wrong on it being a counter. Anyway, I'm replacing the screen in that one. A buddy of mine has a factory SDNA and a DIY and both of his read 2 - and do not change. Neither of them. One is having intermittent problems - the other has no problems at all. Any ideas on that ? Link to comment Share on other sites More sharing options...
RobMidi Posted September 16, 2016 Report Share Posted September 16, 2016 So, last night, the screen on my SDNA 75 went dead, although the mod still fires. Today, I went into the escribe software, clicked into the "service menu" and then selected Device Monitor tab. While looking at the "screen disconnect" field, it kept counting upward, starting at about 150 and is now above 200. It increments sequentially about once every half second. Thoughts? Link to comment Share on other sites More sharing options...
VapingBad Posted September 16, 2016 Report Share Posted September 16, 2016 The screen cable has either come loose or is damaged. Link to comment Share on other sites More sharing options...
cobalt327 Posted September 17, 2016 Report Share Posted September 17, 2016 I'm not seeing a 'service menu' nor a 'screen disconnect' field anywhere- is this from an older version of escribe? I'm using escribe software version 1.2 SP3 w/the latest SNY SDNA mod firmware. Is there a screen disconnect field, and if so how to access it. Link to comment Share on other sites More sharing options...
RobMidi Posted September 17, 2016 Report Share Posted September 17, 2016 In escribe, go to "Help" and select "about". Click on the escribe logo about 7 times in rapid succession, and that takes you into the service mode. Then select the tab to monitor the device, and down the left side of the screen, there is the box marked "screen disconnect." Select it. If the value is greater than zero, the screen cable is either disconnected or damaged. Link to comment Share on other sites More sharing options...
Spector NS5 RD Posted September 17, 2016 Report Share Posted September 17, 2016 in escribe, click "help" scroll down to "about escribe" when the window appears, click the evolv logo 7 or 8 times.the window will disappear. then go into device monitor and you'll see a new field that is labeled "debug". in the debug window you'll see "screen disconnect". it will be in seconds if the number is 0 that means your screen is secure in the ZIF connector. if the seconds are counting up or bouncing between anything higher than 0 you have a bad screen connection to the board.EDIT......OH DANG, SORRY, THAT FIELD SEEMS TO HAVE DISAPPEARED???? STRANGE. AT LEAST IT IS ON WINDOWS 7EDIT 2 LOL......IT'S THERE YOU JUST HAVE TO RESIZE THE SCREEN. I FOUND IT BY CLICKING "RESTORE DOWN" IN THE TOP RIGHT HAND CORNER OF THE DEVICE MONITOR WINDOW THEN I DOUBLE CLICKED THE TOP EDGE OF THE WINDOW AND SHRUNK IT UNTIL THE HIDDEN FIELDS COME OUT FROM UNDER THE "STATISTICS" PART OF DEVICE MONITOR. Link to comment Share on other sites More sharing options...
VapingBad Posted September 17, 2016 Report Share Posted September 17, 2016 For a DNA 200 debug fields I need to use a 1080p monitor in portrait orientation to fit all the fields on, window > 1090 px high & no scrollbars. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now