Zodiac Posted October 13, 2016 Author Report Share Posted October 13, 2016 Just noticed that there is a, delay from +/- 1,5 sec when I fire my VT75, this is quite annoying. Is there a fix, or can I solve this maybe with pre-heat ? Link to comment Share on other sites More sharing options...
retird Posted October 13, 2016 Report Share Posted October 13, 2016 Can you use Device Monitor and fire the device for 5 seconds and take a screenshot of the Device Monitor data and post it here? Link to comment Share on other sites More sharing options...
Zodiac Posted October 13, 2016 Author Report Share Posted October 13, 2016 Thanks for your reply !I made some, screenshots while firing, I hope that they are for use. Link to comment Share on other sites More sharing options...
VapingBad Posted October 13, 2016 Report Share Posted October 13, 2016 That looks like almost no delay, are you vaping in temp mode as it looks like you have live ohms checked in the 1st one with the cold ohms too high or locked res and no preheat. Link to comment Share on other sites More sharing options...
Zodiac Posted October 13, 2016 Author Report Share Posted October 13, 2016 Ok, could be almost no delay, for what I noticed it,s very short maybe 1 sec or just bit a shorter, as my mech fires instantly, the VT75 has a bit of a delay.I made the screenshots, after use of the battery-analyser, cause I just received 2 IJOY 26650 batts, I was using ss316L/24 gauge reading 0.7ohm by 40 watts for the, battery-analyser.So I test fired, like you asked, as far as I know this was in power-mode, no preheat set and did not use temp-mode or locked the res. Link to comment Share on other sites More sharing options...
VapingBad Posted October 13, 2016 Report Share Posted October 13, 2016 That looks like a lot less than a second delay in power delivery, I think you mean the the coil take a second to get up to temp, which would just be the coil not the mod. Cold res doesn't matter if temp limiting is disabled. If I were you I would use temp limiting and preheat, it works very well with ss, I even have triple twisted dual coil SS316L builds.Also with less advanced many mods sold as VW only measure the res at the beginning of the puff and set the voltage, so with ss the power goes down as the coil heats just like a mech, DNAs give a flat power output even if the resistance. So the vape will be different between boards with ss and maybe that is why it seem slow to you. Link to comment Share on other sites More sharing options...
Zodiac Posted October 14, 2016 Author Report Share Posted October 14, 2016 First, thanks for your reply and provided info, much appreciated bro ! Finally, I nailed it yesterday-evening thanks to your info, after weeks of frustration, reading, watching reviews etc, etc, almost sold it, but know I am very pleased with it ! Chanced some profiles in EScribe, made a ss316 clapton build reading 0.3ohms, add the standard ss316 profil, TC off, pre-heat on, for 0.5 sec by 55watts, cause I like it a bit smooth and it fires also even a more directly now. Found my way know, thanks ! Btw, can you put in the TCR manually. Link to comment Share on other sites More sharing options...
VapingBad Posted October 14, 2016 Report Share Posted October 14, 2016 You can create a custom material in EScribe and manually set/edit a TCR, just be aware when you edit it the value is the default and not the current value because it is not stored as a single number TCR. Link to comment Share on other sites More sharing options...
Zodiac Posted October 15, 2016 Author Report Share Posted October 15, 2016 Thanks again bro for helping me out ! Link to comment Share on other sites More sharing options...
VapingBad Posted October 15, 2016 Report Share Posted October 15, 2016 You're welcome Link to comment Share on other sites More sharing options...
Zodiac Posted October 15, 2016 Author Report Share Posted October 15, 2016 Need your help again, unfortunately..was just looking at some, things in the device-monitor, switch on puff..when I wanted the use the device it said..return to researcher. Did Google that, readed the manual, went back in the device-monitor switch puff of, but I still get the message..return to researcher ? Link to comment Share on other sites More sharing options...
VapingBad Posted October 15, 2016 Report Share Posted October 15, 2016 I have never seen that, but would check the research tab in escribe, specifically that the puff, energy and time limits are set to disabled. Here is what the defaults look like. Link to comment Share on other sites More sharing options...
Zodiac Posted October 16, 2016 Author Report Share Posted October 16, 2016 Checked the research tab, the puff, energy and time limits where set to disabled, So I set it back to manufactures settings, after that it functioned...the problem occurred, probably due use of the CSV file for Preheat in Kanthal, did download it yesterday used it last night, with the same fused-clapton build it worked very fine, but tonight it went a bit strange, suddenly temp-protected showed up, so I don,t know of that has something to do with it. Link to comment Share on other sites More sharing options...
VapingBad Posted October 16, 2016 Report Share Posted October 16, 2016 As far as I understand it you should only get that message in relation to stuff set on research tab. Link to comment Share on other sites More sharing options...
Zodiac Posted October 16, 2016 Author Report Share Posted October 16, 2016 Your wright it did not showed up again, had probably something to do, that I switch on puff, in the device-monitor, before it showed up. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now