[DNA200 now has higher output voltage with 4-25 firmware.]

I rolled 3 of mine back within a couple of hours but I used the 2016-02-29 EScribe to do it.
mikepetro did you do yours with the beta EScribe?

[Evolv, will you survive?]

Over on the "big forum" it goes like this "you can attack the post but don't attack the poster. I think that can work here too.

[Updated to 4-25? Have fun with that firmware FOREVER.]

Try using an earlier version of EScribe, one listed as testing or recommended.
I reverted 3 of mine back to earlier FW from 4-25

[DNA200 now has higher output voltage with 4-25 firmware.]

Csd113 said:

i cant get the update firmware promt to occur on the new escribe 75

From what I gather only the newer firmware that's included is only for the DNA75. 
I tried to flash one of my 200's with the 75's firmware and it couldn't see the device.
(EScribe version 1.0.56) 

[Bad battery or board?]

Any juice under the balance connector on the board maybe? Or flux.

[MOD stopped working]

 

 

[DNA75 escribe?]

Great news......
But still in no hurry, It will be at least 30 days before my 75 arrives.

[RIP my chip Dna200]

Might I ask what firmware version that you were using?

[DNA75 escribe?]

Looks like Hcigar got their DNA boards mixed up.

[DNA75 escribe?]

The version that was on Evolv's site and removed was dated 04-25-16
The one on Hcigar's site is newer, 05-02-16

[DNA75 escribe?]

I'm going to wait till Evolv suggests that we try the beta DNA75/200 software before I try it again. (I took out the earlier one almost immediately). As much as I would like to use it I'm going to wait, my devices currently work just fine.

[please help me wiring a 2s lipo]

I was only guessing on that, great that it's working for you.
Edit: So I studied the diagram some more and can't see how it wouldn't work......but I believe you.

[please help me wiring a 2s lipo]

I think that the short black and short red wire could have been omitted but I'm just guessing.
I believe that + an - on the balance taps are connected internally on the board to battery +and -. 

[please help me wiring a 2s lipo]

Same for 2S Lipo
https://forum.evolvapor.com/topic/66226-topic/?do=findComment&comment=895167

[Temp control Issue]

Axis Vapes site states that they use a Varitube 22 mm flat 510. I have one in front of me and the output wire gets soldered into the 510 pin same as a FDV v3 and just about all others. Still could be a problem with the spring or the insulator (from excessive heat) but the spring is not part of the electrical path.
I'd be checking this with atomizer analyzer in EScribe as well a comparing live ohms and cold ohms between the two mods using the same (cooled) atty in device monitor. Note the percentage the ohms changes from cold to hot with same settings.
Also what is mod resistance set to on the M17?

[EFusion Duo - 2 LG HG2 - Imbalanced battery error {Solved}]

The idea of changing the numbers threw in an added element of confusion, I had to sketch it out and refer to my extra lipo's plug.
I should have just put the two pictures up in front of me, it would have been easier.

[EFusion Duo - 2 LG HG2 - Imbalanced battery error {Solved}]

 

I'm missing something here.
Warning this plug is numbered incorrectly, should be from left to right 3, 2, 1, gnd

[EFusion Duo - 2 LG HG2 - Imbalanced battery error {Solved}]

BillW50 said:

Whoa! Are you sure dwcraig1? Three cells should be wired using Fred's pin numbering would be:

3+4 = cell 1
2+3 = cell 2
1+2 = cell 3
1+4 = sum of cells 1+2+3

On two cells it should be:

3+4 = cell 1
2+3 = cell 2
3+4 = should be a dead short.
1+4 = sum of cells 1+2

Using the diagram in post #6
I have double checked it and got the same as I previously posted.
Is the diagram in post #6 correct?

[EFusion Duo - 2 LG HG2 - Imbalanced battery error {Solved}]

Can't you check it for continuity?
Between the bridge between the two batteries and which ever pin the white wire goes to.

[EFusion Duo - 2 LG HG2 - Imbalanced battery error {Solved}]

Here's the voltages using your pin numbering and  batteries @ 4 volts ea. 
1 + 3 = 4 volts
2 + 3 = 4 volts
1 + 4 = 8 volts
2 + 4 = 8 volts
3 + 4 = 4 volts
1 + 2 are bridged so 0
Anyone using this just keep in mind that the pin numbers being used are not Evolv's numbers

[SS 430 Probably will putting all my other wire in the "box"]

The coil
 

[EFusion Duo - 2 LG HG2 - Imbalanced battery error {Solved}]

My guess is there's something wrong with the balance connector or it's wiring on the sled. Take a good look at the pins of the jst connector of the sled also.
Measure the voltages off the balance connector. I'll have to locate what they are, I'll be back.
Maybe this will help:
https://forum.evolvapor.com/topic/66226-topic/?do=findComment&comment=895167
 

[Reuleaux dna200 screen]

Yes
http://evolvapor.com/dna200.php
2nd item on page.
A bit of instructions here, more to be found on this forum.
http://evolvapor.com/datasheet/dna200.pdf

[SS 430 Probably will putting all my other wire in the "box"]

black lace said:

Dwcraig2:- what do you mean 4 strands? 4 twisted or four loops of a coil and what size mandrel, because im having doubts that the 430 that ive got is what i paid four, a device monitor screen shot would just show caos compared to yours.

I put two lengths of 28 gauge SS 430 in my drill and twisted them pretty tight, repeated using another two pieces resulting in two lengths of twisted pairs.
Then I put the two pieces of twisted pairs into drill and twisted them in the opposite direction that they were previously twisted. Wrapped about 7 times, 3 mm id.

This is the end piece that I didn't use.

[DNA75 escribe?]

retird said:

What Version of EScribe are you running?  

1.0.51
04/25/16