-
Posts
2,322 -
Joined
-
Last visited
-
Days Won
146
Content Type
Profiles
Forums
Downloads
Posts posted by dwcraig1
-
-
I'm inclined to think that the mods with the lower resistance is closer to correct. I can't remember a DNA60 reading less, only higher.
For sure zero is not the correct setting, usually 0.004 or higher.
To check the mod resistance use atomizer analizer with a shorting 510 plug with mod resistance set to zero. Screw the shorting plug into the mods 510 and put the resulting figure into the mod resistance (electrical tab) and upload to device.
I use a cartomizer that I soldered over it's 510 connection, it works great. This could be done also with a 510 to 510 adapter or an old atty with brass base/510.
- 1
- 1
-
This is an old video using an old version of EScribe but explains it well.
- 2
-
-
What brand of mods do you have. Example: Dovpo College DNA60
- 2
-
-
9 hours ago, jorge diez said:
MUY BUENO...PERO, DONDE ESTA EL ARCHIVO es.po ?...te lo cuento porque me lo he descargado, y resulta que esta el archivo x.po de varios idiomas, pero el del es.po brilla por su ausencia. Gracias por subir la info de todas formas.
https://forum.evolvapor.com/applications/core/interface/file/attachment.php?id=239477
- 1
- 1
-
When using Atomizr Analyzer how many turns more does it take to screw in all the way once a correct resistance starts showing? There is no 510 standard so some are shorter and don't contact well with the mod's 510, check for that.
- 1
-
-
It is normal for resistance to slowly rise when using Atomizer Analyzer as a vrey small amount of power is being applied. The resistance change in you previous post appears normal to me.
It should be slowly going up, not up and back down and up and down.
-
It appears to not be stainless steel, probably Kanthal or Nichrome.
- 1
-
Hover mouse curser over area indicated by red arrow and report back what the voltage reads.
Also it appears that the standing voltage of your cell is 3.66 volts, with a 75 ohm load it very well is going to drop to below the 2.75 volt cutoff and do exactly what you are posting about, throttling down.
Does charging the cell to full charge correct this problem?
-
-
-
Even though your charger outputs 4.5 amps the board will never draw more than 2 amps, so no problem.
Pay attention to cell voltage rather than percentage, 4.1v - 4.2v is full charge. If they are not close in voltage between each other charging will appear to stop while it balance charges which is quite slow.
One more thought, have you tried using a different cable?
-
On all your screens the settings look good. After you did the reset is it possible that it changed from 2 cells to 3? If so change it back to 2 and upload settings.
You have it set for maximum recharges which is fine but charging wil stop at around 94%
On your 1st screen those wavy lines are not good.
-
The best work around would be to lower the wattage down and take long slow hits.
- 1
-
As Bill said "batteries can explode" and those salvaged laptop batteries are of the chemistry that does it best. Laptop batteries are generally 4 to 5 amp continuous discharge rated. To supply 100 watts from the board cells with a rating of 15 amp minimum would be required. Personally I would use 30 amp rated cells. You are running a huge risk by over taxing them. If you want to salvage cells from something power tool batteries would be a good source, though I wouldn't recommend doing that either.
- 1
-
I had the same problem with the Windows version on my DNA60. James fixed it right away, try downloading and installing again.
- 2
-
I don't know, I'd be pretty exited too if an expensive mod like that malfunctioned.
- 1
-
Sp55.1 did nothing on either one of my 100's in the mod resistance area. Just the usual ? I got it to briefly flash 0.010 once.
- 1
-
I must admit that I hadn't tried it since updating the FW, I shall get on it when I get home from work
- 1
-
-
-
It has to do with which firmware your device is using. The latest firmware for your device is included in this EScribe Service Pack. It will change wattage in 1 watt increments.
https://downloads.evolvapor.com/SetupEScribe2_SP45_INT_ServicePack.exe
Mod resistance Lower than any other dna60 mod
in General Discussion
Posted
Be aware that the zero in the box is not the mod resistance, this is just what it is set to. Put your value in the box and upload to device.