Fabio1909 Posted July 3, 2017 Report Share Posted July 3, 2017 Hallo an alle, ich habe eine think Vape Finder 167w in kombination mit einem Taifun BT, ich kann bei 0,40 ohm nicht höher als 87w befeuern sonst kommt die Meldeung :ohms too high mit anderen Akkuträgern gibt es keine probleme.Kann man das irgendwie ändern?Bitte um Hilfe. Sorry das ich kein Englisch kann. Link to comment Share on other sites More sharing options...
Wayneo Posted July 3, 2017 Report Share Posted July 3, 2017 Klingt wie Sie schlagen die 6 Volt Ausgangsspannungsgrenze. Verwenden Sie Dampf-Motor und ändern Sie Ihren Build (niedriger), wenn Sie höhere Watt wollen, wissen, dass Einschränkung Sounds like you are hitting the 6volt Output voltage limit. Use steam-engine and change your build (lower) if you want higher watts, knowing that constraint Link to comment Share on other sites More sharing options...
Fabio1909 Posted July 3, 2017 Author Report Share Posted July 3, 2017 Mit dem Taifun bt kommt man nicht viel tiefer mit den Ohm, das ist ja das problem!Kann man nicht irgendwie die 6v grenze auf 9v erhöhen beim DNA 250 Chip mit 167Watt ?? Link to comment Share on other sites More sharing options...
67exec Posted July 3, 2017 Report Share Posted July 3, 2017 The dna250 doesn't have a boost circuit. You would have to make it into a 3cell mod to get the 9volt limit Link to comment Share on other sites More sharing options...
Fabio1909 Posted July 3, 2017 Author Report Share Posted July 3, 2017 oh ok, dann bin ich echt enttäuscht! werde das gerät wieder verkaufen!! selbst meine billige evic primo mit 2 akkus kann 9v Link to comment Share on other sites More sharing options...
67exec Posted July 3, 2017 Report Share Posted July 3, 2017 (edited) The advantage of this boost is that it can not be used in Edited July 3, 2017 by 67exec Link to comment Share on other sites More sharing options...
Fabio1909 Posted July 3, 2017 Author Report Share Posted July 3, 2017 ist für mich trodzdem ein grund das gerät wieder zu verkaufen! ich wollte extra einen schönen akkuträger für meinen taifun bt haben und jetzt kann ich damit nicht soviel anfangen Link to comment Share on other sites More sharing options...
67exec Posted July 3, 2017 Report Share Posted July 3, 2017 My phone is stupid... Anyway my last reply was supposed to say that the dna 250 is 97% efficient because of no boost circuit. Boost circuits are 65%-85% efficient, which means that 15%-35% of you battery Wh is wasted as heat Link to comment Share on other sites More sharing options...
teano718 Posted September 13, 2017 Report Share Posted September 13, 2017 (edited) I am having this same problem. Reads "ohms too high" when batteries reading a little below half @ 65w .55ohm single clapton coil. Unfortunately I can't understand what happened with the OP because it's all in German. I am running 2x18650 LG hg2 3000mah Edited September 13, 2017 by teano718 More info Link to comment Share on other sites More sharing options...
Wayneo Posted September 13, 2017 Report Share Posted September 13, 2017 2nd post in this thread is probably the issue. Definitely English in there Link to comment Share on other sites More sharing options...
teano718 Posted September 13, 2017 Report Share Posted September 13, 2017 Idk what's wrong then because every post im seeing from Fabio1909 on this is in German. And there's no need for the arrogance. What a warm welcoming to a new member... Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now