tageeboy Posted September 30, 2015 Author Report Posted September 30, 2015 I am still getting up to speed with all the amazing options that come with the DNA 200. Like a lot of the other folks in the vape world I started with gen1 Kanger on a stick battery, mech, AVP, VW VV box, TC, and now the DNA200. I have a museum here. So where I am having issues is with building a Ti profile. I went to steam engine but I must be missing something. My settings come out too low when I upload them. I get a line that is almost straight across the screen after selecting Ti wire. Would it be possible to start a repository online where we could download other people's csv files? Sorry if this is an inapproprate question. I am not being lazy, just really struggling with TI and miss having that option for building. Kanthal is working insane great, I don't build with NI due to the difficulty and softness. Ti has been my fav with my IPV4 and VTC Evic. Any help would be much welcomed. Sorry to make my first post "hey, can ya help me".
druckle Posted September 30, 2015 Report Posted September 30, 2015 The titanium temperature coefficient of resistance is basically a straight line in the temperature region of interest for vaping. The steam engine .csv is working fine for me.
tageeboy Posted October 1, 2015 Author Report Posted October 1, 2015 I tried it again and noticed I had not entered anything for the resistance. I added the info there from the current coil build and it seems to be working like a charm. Thanks for the response. Back on track.
p1554nt Posted October 3, 2015 Report Posted October 3, 2015 I would like a .csv file for a sense cyclone stainless build.When I try to put what I think it is by the measured ohms it barely fires.I am also having a hard time finding the specs on the s.s. coil head to punch into steam engine.Even if someone can help nudge me into some settings to look for or other help for me to make my own i will post .csv file.btw. here is a logo file name marked as other size but it is correct & works.
Dampmaskin Posted October 4, 2015 Report Posted October 4, 2015 Go to Wire Wizard, select SS 316L instead of Kanthal, click DNA 200 and download the CSV. You don't need to change the gauge or number of wraps.
p1554nt Posted October 4, 2015 Report Posted October 4, 2015 Thank you for taking the time to respond.I'm still getting the same issue.I don't get any vape (or voltage) till i take into the 500 degrees area.It seems to work well on nickle setting but i don't thing it is actually temp protecting it.I am off work tomorrow & will have time to experiment better. especially if i burn my coil.i will make a new thread tomorrow with my results. My apologies if I nudged thread into a self serving question everyone.
Freshcut Posted October 9, 2015 Report Posted October 9, 2015 Just got a Vt200 paired with tfv4. Im using the dual rba with titanium wire. 26awg 10wraps and got a 0.25 build. Upload csv file for ti. Set tc at 350F. Unfortunately, TC kicks in after abouy 7 puffs of 30watts. Is this normal?
scoopy Posted October 10, 2015 Report Posted October 10, 2015 Ya 350 don't take long at all to hit.....I vale mine at 520
Freshcut Posted October 10, 2015 Report Posted October 10, 2015 Wont your cotton or coil burnt at that temperature? Im getting tired recoiling over and over again. Going to the prebuild. Btw, how does the preheat value in escribe works?
scoopy Posted October 11, 2015 Report Posted October 11, 2015 No because it knows when the cotton is dry.... The preheat works by heating your coil to the preheat temp then throttles back right before it gets there..... its so the coil basically gets to the temp u want it at instantly without having to wait on it to heat up
Freshcut Posted October 11, 2015 Report Posted October 11, 2015 Right. So i set mine at 520F 30Watts. Everything was good but at my 5 or 6 puffs, once i fire i had a nasty vapour. Its like i burnt it into flame. What could be the issue.
Lipoid Posted October 11, 2015 Report Posted October 11, 2015 Maybe wicking issues.I have the TFV4 with dual deck.Using twisted 26 gauge T1 , 2mm inner , 5 wraps comes out @ .1 Ohms.Settings as follows.400f , 50 w , 120w preheat , 9.1 preheat punch for 2 seconds.Airflow is 2/3 open & i usually take a 3 to 4 second hit.If i take a real hard hit it does not reach Temperature Protection(2 mm allows good airflow around coil),a more lazy hit & it does.As long as i wait to see the air bubble rise after each hit no scratchy/dry hits & the bubble rises normally before i have done a lazy exhale.YMMV depends on your juice , how hard & often you vape.
Freshcut Posted October 11, 2015 Report Posted October 11, 2015 Was comparing same tank same builf diff mods. Ipv4s and vt200. The ipv4s works better and no dry hits at all. And suddenly my VT200 turns off. Cant even turn it on. Damn it... Its already so difficult to get one here.
scoopy Posted October 11, 2015 Report Posted October 11, 2015 Also u can turn off the message that says temperature protection if u don't want to see that every time u hit it
Freshcut Posted October 12, 2015 Report Posted October 12, 2015 Well... My VT200 is already dead. Sending it back. So mush time so much $ just for it to die on me. Hcigar & Evolve please do. Something.
scoopy Posted October 12, 2015 Report Posted October 12, 2015 If Hcigar don't I'm absolutely sure Evolv will......As Nick stated in one of his threads if the mod maker don't help open a ticket with Evolv and they got your back and will be glad to help....Evolv is excellent when it comes to customer support
Freshcut Posted October 12, 2015 Report Posted October 12, 2015 Great to know that Scoopy. Well i managed to get Hcigar through Facebook. Waiting for their email patiently.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now