Kudabau Posted October 13, 2016 Author Report Share Posted October 13, 2016 Im having trouble with check battery with device finder 133 dna chip 200 from thinkvap My device cant turn on , when im firing the device on and when i release firing button it shut down the device, my mod show check battery It will turn on via usb plug only And when i check via escribe in device monitor cell 1 is dead on 0.01 and cell 2 at 5.00 cell 3 at 1.2 .finder is 2 battery mod im already set my my battery wattage at mod. Im using 2 battery like samsung lg, still dont work This is common problem with this device in indonesian Can somebody explain Link to comment Share on other sites More sharing options...
Spector NS5 RD Posted October 14, 2016 Report Share Posted October 14, 2016 welcome to the forum Kudzako. you can try hard and soft reboot from escribe and also try re-flashing the firmware. the reason the device will not stay on is because it's not reading one of the cells, more of a symptom than a cause. you either have a bad/broken connection regarding the battery to the board or the board has failed. you're 100% positive BOTH cells are fully charged and balanced? if you are, then you need to return the device.just last week, my VS Vaporflask 133 displayed the same problem as you're describing. i had to send it back to VS for a new DNA 200 board. Link to comment Share on other sites More sharing options...
Kudabau Posted October 14, 2016 Author Report Share Posted October 14, 2016 Im already try soft and hard reboot but it keep sending me notification cant. My battery already 100% and balance, so i must open ticket to evolv or what ? Im from indonesian Link to comment Share on other sites More sharing options...
Spector NS5 RD Posted October 14, 2016 Report Share Posted October 14, 2016 the device, most likely, cannot be repaired by using Escribe. i would contact the vendor you purchased the mod from first and see what they say. if their response is poor or you receive no response, then yes, open a help ticket with Evolv from their webpage. Link to comment Share on other sites More sharing options...
EndraDAce Posted October 16, 2016 Report Share Posted October 16, 2016 Kudabau said:Im having trouble with check battery with device finder 133 dna chip 200 from thinkvap My device cant turn on , when im firing the device on and when i release firing button it shut down the device, my mod show check battery It will turn on via usb plug only And when i check via escribe in device monitor cell 1 is dead on 0.01 and cell 2 at 5.00 cell 3 at 1.2 .finder is 2 battery mod im already set my my battery wattage at mod. Im using 2 battery like samsung lg, still dont work This is common problem with this device in indonesian Can somebody explain same problem with me few days ago when i purchase finder 133. i even doesn't have a chance to use it and it shows same like yours. But now i can use it, i don't know how to repair it, but when i give it to my friend whose expert, he's playing with EScribe and under 5minutes it's Fixed!!Maybe you should ask your friends or you can go to vape store on your city to ask it, maybe they can fix iti just bought it 5 days ago, and now i considering of sell it and buy a Lost Vape Therion 133. I'm afraid that my Finder133 going insane again.saya dari indonesia juga. hahaha Link to comment Share on other sites More sharing options...
roidfaqih Posted October 16, 2016 Report Share Posted October 16, 2016 yang dari Indonesia benerin dimana om? cell 1 sama 2 nya normal?sy pake finder 133 jg. Dan baru 3 gari slalu check baterry, dan akhirnya dilembiru karna cell 1 nya selalu 0.01v Link to comment Share on other sites More sharing options...
donysaurus Posted November 4, 2016 Report Share Posted November 4, 2016 Hi all,I do have the same problem today.It happen after i escribe my Finder 133.Almost desperate, but then i try to check the escribe software, then finally.You should Try to update the firmware of the mod to early update. Don't forget to backup all your settings before did the update. Then open the escribe software, choose Option -> User Interface -> Manufacturer.Ussually if we don't choose the User Interface, the default is Clean.Then choose Mod tab. You will see Battery option. Beside the Capacity text box, there is a drag option bar, the default is 3-cell. If you are using Finder 133 with 2-cells battery, as i am, then you have to change the value become 2-cells. Then click the Watt-hours calculator to get the capacity value. The variable is written in your battery. Fill the Capacity text box after you calculated it.Then upload the settings. Voila....you did it. hehe.If this can't solve your problems, maybe others have another way.Just share my thought.Btw, coba aja dulu mas. Siapa tau bisa. Karna saya juga berhasil.Thanks Link to comment Share on other sites More sharing options...
Kaitokid Posted November 5, 2016 Report Share Posted November 5, 2016 Not working bruh, ada solusi lain ? Link to comment Share on other sites More sharing options...
donysaurus Posted November 7, 2016 Report Share Posted November 7, 2016 Kaitokid said:Not working bruh, ada solusi lain ?Itu aja solusi dari ane bro...kalo ga bisa juga, mungkin hardware bro. Link to comment Share on other sites More sharing options...
MiunTurbo Posted November 16, 2016 Report Share Posted November 16, 2016 donysaurus said:Hi all,I do have the same problem today.It happen after i escribe my Finder 133.Almost desperate, but then i try to check the escribe software, then finally.You should Try to update the firmware of the mod to early update. Don't forget to backup all your settings before did the update. Then open the escribe software, choose Option -> User Interface -> Manufacturer.Ussually if we don't choose the User Interface, the default is Clean.Then choose Mod tab. You will see Battery option. Beside the Capacity text box, there is a drag option bar, the default is 3-cell. If you are using Finder 133 with 2-cells battery, as i am, then you have to change the value become 2-cells. Then click the Watt-hours calculator to get the capacity value. The variable is written in your battery. Fill the Capacity text box after you calculated it.Then upload the settings. Voila....you did it. hehe.If this can't solve your problems, maybe others have another way.Just share my thought.Btw, coba aja dulu mas. Siapa tau bisa. Karna saya juga berhasil.Thanks thanks untuk tutorial nya broo Link to comment Share on other sites More sharing options...
jackson1992 Posted December 16, 2016 Report Share Posted December 16, 2016 Mine has the same problem too. And i have followed your instruction in changing the battery from 3 cells to 2 cells but it doesnt seem to work. Does anyone has anymore instruction to do or should i just contact my local vendor for this problem?Any help is appreciated. Cheers Link to comment Share on other sites More sharing options...
putramahendra Posted December 20, 2016 Report Share Posted December 20, 2016 Change Type Battrey To Power Supply..I Think It's Work... Link to comment Share on other sites More sharing options...
VapingBad Posted December 20, 2016 Report Share Posted December 20, 2016 Power Supply mod would need 9 - 12 V and you shouldn't leave it in this mode with batteries I think it bypasses some of the battery protection.Yes Jackson, I would contact your vendor for repair or replacement. Link to comment Share on other sites More sharing options...
putramahendra Posted December 20, 2016 Report Share Posted December 20, 2016 It's temporary solution Link to comment Share on other sites More sharing options...
Yph Posted December 21, 2016 Report Share Posted December 21, 2016 Last night it happened to my therion 133 DNA 200. The device just shut down automatically, I plugged it in to USB escribe and it said check battery. One of the cell is not detectable, I tried to reset and hard reset or change the battery from 3 cell to 2 cell still no luck. This morning, I decided to disassemble it. Found the problem of my therion 133. One of the cord that connected to the battery is not attached (there are 2 cords, red and black and in my case the black one). So I managed to fix it and now it's working as usual. Semoga bisa ya agan agan yg dari Indo. Dibongkar manually saja. Kalau masalah dari chip nya aku rasa ga ada. Oyah untuk menyambungkan lagi kabel nya, jelas ya butuh soder dan kawat nya dan untuk therion 133 harus dilepas deck kayu kiri kanannya. Good luck. Link to comment Share on other sites More sharing options...
putramahendra Posted December 21, 2016 Report Share Posted December 21, 2016 Yph said:Last night it happened to my therion 133 DNA 200. The device just shut down automatically, I plugged it in to USB escribe and it said check battery. One of the cell is not detectable, I tried to reset and hard reset or change the battery from 3 cell to 2 cell still no luck. This morning, I decided to disassemble it. Found the problem of my therion 133. One of the cord that connected to the battery is not attached (there are 2 cords, red and black and in my case the black one). So I managed to fix it and now it's working as usual. Semoga bisa ya agan agan yg dari Indo. Dibongkar manually saja. Kalau masalah dari chip nya aku rasa ga ada. Good luck. Saya sudah selesai melakukan pembongkaran semua tidak ada konektor yang saya temui lepas, device i finder 157 Link to comment Share on other sites More sharing options...
Yph Posted December 21, 2016 Report Share Posted December 21, 2016 putramahendra said: Saya sudah selesai melakukan pembongkaran semua tidak ada konektor yang saya temui lepas, device i finder 157 Bro punyamu kalau dicolok ke escribe ke detect ga? Kalau ke detect coba liat di bagan battery, apakah voltage nya sama antara cell 1 dan 2? Kabel yg lepas bisa di bagian atas konektor battery atau di bawah. Kebetulan punya ku keliatan langsung di bagian atas tanpa harus membongkar total lempengan lempengan battery. Saran aja sih coba di Check lagi di konektor battery nya apakah bener bener soder An nya ga ada yg lepas. Good luck Link to comment Share on other sites More sharing options...
putramahendra Posted December 21, 2016 Report Share Posted December 21, 2016 Yph said: Bro punyamu kalau dicolok ke escribe ke detect ga? Kalau ke detect coba liat di bagan battery, apakah voltage nya sama antara cell 1 dan 2? Kabel yg lepas bisa di bagian atas konektor battery atau di bawah. Kebetulan punya ku keliatan langsung di bagian atas tanpa harus membongkar total lempengan lempengan battery. Saran aja sih coba di Check lagi di konektor battery nya apakah bener bener soder An nya ga ada yg lepas. Good luck Gini bro, semalem gw udh bongkar semua nih device nya, tetapi gw gk jumpai yang yang namanya konektoe putus. Semua aman bro.. Gak ada cacat sama sekali secara fisik... Lalu ane coba colokin ke escribe. Gw chek cell batrey yang cell 1 nya itu 0.59 yang cel 2 itu 5.23 yang cell 3 nya disable.. Soalnya ane pakai mode 2 cell bat... Tapi kalok di ganti mode power suplay it's work... But ini sebagai solusi sementara Link to comment Share on other sites More sharing options...
Yph Posted December 21, 2016 Report Share Posted December 21, 2016 putramahendra said: Gini bro, semalem gw udh bongkar semua nih device nya, tetapi gw gk jumpai yang yang namanya konektoe putus. Semua aman bro.. Gak ada cacat sama sekali secara fisik... Lalu ane coba colokin ke escribe. Gw chek cell batrey yang cell 1 nya itu 0.59 yang cel 2 itu 5.23 yang cell 3 nya disable.. Soalnya ane pakai mode 2 cell bat... Tapi kalok di ganti mode power suplay it's work... But ini sebagai solusi sementara Sama bro. Kemarin therion 133 gw juga gt. Cell 1 0.sekian n cell 2 5.sekian. Kebetulan aja mungkin therion gw, gw bongkar and dapat 1 kabel lepas pas ke penghubung battery dari head nya bagian atas. Buat case mu... Good luck Bro... Ga ngerti juga kenapa gt. Kayaknya evolv banyak problem juga ya di chip nya. Jadi mikir ganti Mod yg lain. Link to comment Share on other sites More sharing options...
putramahendra Posted December 21, 2016 Report Share Posted December 21, 2016 Yph said: Sama bro. Kemarin therion 133 gw juga gt. Cell 1 0.sekian n cell 2 5.sekian. Kebetulan aja mungkin therion gw, gw bongkar and dapat 1 kabel lepas pas ke penghubung battery dari head nya bagian atas. Buat case mu... Good luck Bro... Ga ngerti juga kenapa gt. Kayaknya evolv banyak problem juga ya di chip nya. Jadi mikir ganti Mod yg lain. Iya sih bro katanya pihak evolf belum ada solisi sebener e buat masalah ini Link to comment Share on other sites More sharing options...
joseph1203 Posted December 27, 2016 Report Share Posted December 27, 2016 Yph said:Last night it happened to my therion 133 DNA 200. The device just shut down automatically, I plugged it in to USB escribe and it said check battery. One of the cell is not detectable, I tried to reset and hard reset or change the battery from 3 cell to 2 cell still no luck. This morning, I decided to disassemble it. Found the problem of my therion 133. One of the cord that connected to the battery is not attached (there are 2 cords, red and black and in my case the black one). So I managed to fix it and now it's working as usual. Semoga bisa ya agan agan yg dari Indo. Dibongkar manually saja. Kalau masalah dari chip nya aku rasa ga ada. Oyah untuk menyambungkan lagi kabel nya, jelas ya butuh soder dan kawat nya dan untuk therion 133 harus dilepas deck kayu kiri kanannya. Good luck. hi do you have a video on how to disasembled the therion 133? procedure and step by step. Link to comment Share on other sites More sharing options...
Yph Posted December 27, 2016 Report Share Posted December 27, 2016 You can check it on https://youtu.be/gjri569A-Qs Good luck Link to comment Share on other sites More sharing options...
Teo22 Posted January 19, 2017 Report Share Posted January 19, 2017 donysaurus, Thank you for posting #7 on no battery charge and mod stopped working. I followed what you said to do, and now it is better than before!!!! It is working again, and this is my 1st time here, and I thought I cooked it (Evolv VT 133).Thank You,Teo22 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now