hg2 curve for 2 batteries dna 250

[Krisrhodes]

Sorry for the noob question, but I've seen a lot of files for 3 batteries I was wondering if anyone has a file I can plug in for a 2 cell hg2 setup in a dna 250 (167) mod?

[Spector NS5 RD]

this CSV will work for the DNA 200/250.........

 3S_LG_HG2_Battery_Profile.csv     

make sure you input 29 or 30 for the "capacity" or watt hours. 

3 volts for the "cell soft cutoff" value.

this should get your batter meter very close.

[Krisrhodes]

Thanks so much... when I put my tank on and set it to 80 watts (or110 for that matter) it gets up to the mid 70s and fires there... any ideas why?

[giz_60]

Check your Kanthal Power Limit setting in Escribe...Mod tab, just above the battery settings

[giz_60]

Hi ChunkyButt200...is that Wh's for 2 or 3 cells? I too am using the HG2's & after running the battery analyzer, the .csv that was generated almost the same as the one you you attached, but the Wh's are quite a bit lower....16 and my battery meter seems to fairly close so far.

[Spector NS5 RD]

16 watt hours with 2s LG HG's sounds about right. it will work with 2S or 3S setup. what matters is the watt hour capacity you input. in the past, i have ran BA on two LG HG2's and also with a set of 3. both curves were almost identical, only differing in capacity. 17.xx wh for the 2S config, 28.xx wh for the 3S config.

[Krisrhodes]

my kanthal power limit is 250, when i hit it i'm only getting 1.25 volts.. now its sitting around 7 watts... help!!!  my first dna I appreciate all the help

[Krisrhodes]

Here are the changeable values on the mod tam that i have set.. pease tell me if i need to change anything:

K Power Limit - 250
Capacity - 29wh (should this be 16 or 17?)

cell soft cutoff - 3v
Max Peak  - 28A
Max Sustained - 28A

[VapingBad]

K power limit = 167
Capacity = 19 Wh (if the 29 was for 3 batteries)

Doesn't explain your issue though, what metal and resistance coil are you running?

[Krisrhodes]

Kanthal Fused claptons .16
Also tried a TFV8 tank with the same result

[VapingBad]

That shouldn't be a problem, have a look in EScribe - Device Monitor to see if the cell voltages are sagging to 3 V while firing.

[Badger]

ChunkyButt200 said:

this CSV will work for the DNA 200/250.........

 3S_LG_HG2_Battery_Profile.csv     

make sure you input 29 or 30 for the "capacity" or watt hours. 

3 volts for the "cell soft cutoff" value.

this should get your batter meter very close.

Will this Csv file work for a 3 battery Triade 250 as well? i'm also a noob. thanks in advance.

[demin]

ChunkyButt200 said:

this CSV will work for the DNA 200/250.........

 3S_LG_HG2_Battery_Profile.csv     

make sure you input 29 or 30 for the "capacity" or watt hours. 

3 volts for the "cell soft cutoff" value.

this should get your batter meter very close.

Would you send me the file to demin_bdpers39@yahoo.com because i can't download it via this thread. Thanx before

[Andreogon]

Kalau untuk therion 166 DNA250 Kapacity dimasukkan berapa ? Cutoffnya berapa ?