saschacolussi

HW patch? whats that?

Any news on that error? I'm still getting it, and dont have any idea on how to mess with the firmware like you guys adviced

Anyone has anything new on this tread? i'm having the same issues

Thanks a lot, will take a look at the guide later, and will be using SS316L for the test than.

Hi, i've seen a Bill Lee video about the battery calibration guide, but i have a doubt about the method. I'm thinking about doing it using SS316L wire on my rda, what you guys think about it? Is it Safe? Will the results be the same as using kanthal? thanks. PS: The video im talking about

Had this, my problem was that my ohms reading wasnt stable. Had to open everything up on my rda, let it sit on water for a day then clean it troughtfully. After that i wicked it SPACED COIL, and voila, working as a charm

Hey guys, figured what the problem was, i was having really unstable ohm's readings. Disassembled my atomizer cleaned it thoroughly and now it works flawlessly, thanks a lot for the support.

Great man, thanks a lot. Just another question, whats the advantage of setting up the thermal settings? thanks

Theanks for the batteries, but about the thermal, didnt you said that your mod had a problem and had to return it? meaning, the case analyzer you ran should be wrong right?

Hi, been looking for the discharge profile for the vtc5a's did you got it for the triade? Also, saw that you ran the case analyzer but with issues, did you managed to get it right? Thanks a lot mate.

yeah, fuly charged today when i tried it again. Will set my cell cutt off a little lower. Is 3.0 ok? whats the rule regarding this for 18650's? Brand, mah? In wattage its working fine.

i've been reading a little bit, and my ohm on atomizer analyzer seem to be fluctuating a little bit 0,01

i've set it to 250C witho no success. Tried 50w 60w and 70w also with no success. The preheattemp is also off

Forget it, it's doing the same thing now, I've got a few puffs only. Ps: it's a Zeus's x clone

Here are some of my build pictures. Just lowered the power to 50w and preheat to 60w with a punch of 7. It's working now, but why is that? I mean, shouldn't I be able to increase the power, or punch, to reach the desired temperature quicker? Thanks a lot mate.

PS: my soft cell cutt off is set to 3.2V

Hi guys, just managed to achieve what i was talking about. The first picture gets me the temp protected warning with little juice. In the second one, i just dripped juice to see if that was the problem, i was able to vape a little longer but got the same warning too. I tought that with replay it would lower the wattage and allow me to keep vaping but it just cuts the power. Any help woud be apreciatted, thanks.

i', not, i'll be sharing a model so you can print it at home, for free

I tought i should do the opposite. Set the power to what i would usually use with the coil and set the preheat to something a little higher and punch around 10-11, so it would reach the temp 286C quicker

Hi, does anyone has a 3d model of the mod Lost Vape Triade 250c ? Been looking for it because ill make a case for it and share it with you guys.

Thanks but i didnt get it, should i be worried about the voltage than? "he DNA 250C runs from up to a four cell battery. Because lithium polymer cells can be damaged by excessive discharge, with multi-cell series batteries it is important to measure each cell in the battery independently and stop firing the atomizer when any of the cells reaches the cutoff voltage. The DNA 250C uses the battery pack taps to monitor each cell." Those 24amps i cited, isnt it from each cell than?

Here's my battery cell cut off. I didn't manage to recreatethe situation above, but as soon as i get that i'll post it here, thanks for the help.

Alright but those 30amps pulled from the batteries are safe? I mean, my batteries are approx. 20amps each

Still haven't tried the spaced coils, but here's what i was taking about. On the left the replay mode works just fine, on the 2nd puff it just stops working and on and on. Mod max output temp 315,5°C

Hi guys, i've been vaping when looked at my device's screen and it stated that the mod was pulling"24 amps from the batteries at approximately 100W. Does that mean it's 8amps per battery or 24amps going through each one? Would be very happy if anyone could answer me this. I've got 3 Sony VTC5a in there, thanks in advance.