Jump to content
Evolv DNA Forum

Pjr

Members
 View Profile  See their activity

  • Posts

    20

  • Joined

  • Last visited

 Content Type 

Posts posted by Pjr

  10. Best setup for the Paranormal DNA 75c

    in General Discussion

    Posted

    Al last! I have found the best setup for my Paranormal DNA 75c. I have experimented on almost 25 atomizers from rbas, rdas, rdtas and rtas since I started vaping. I would like to share this with you guys. This has given me the most satisfying vapor and never ending flavor as I chain vape everyday. 😊

    Ohms .77 upto 1.0 

    Interval is 5 to 10 mins every 3 to 4 hits daily

    I use cotton bacon v2 

    Just right snug not too tight not too thick

    Wicks should be longer so there will be no dry hits

    I use a kclapton 26g 32g coil and build a 3.5mm 6 loops on my single coil zeus rta. The build should be as high as possible to get an awesome flavor.

    I run my paranormal dna 75c at 30 to 40w 

    My batteries are

    Vtc4 the best battery and with my current build this could last for the entire day and mod does not warm up or get hot at you vape.

    Cylaid

    Strong for the first 6 hours then once it hits 25% it is as good as zero power

    Lg choco

    Performance in variable mods is good and safe, however the aromizer gets warm easily and so as the mod. 

    I highly recommend vtc4 as I use it for most of my variable setups 

    It is as good on a series mod too judt a shorter battery life as compared to my dna 75c which is a dual parallel mod

  12. Ohms jumping a bit while vaping

    in General Discussion

    Posted

    Hi guys! 

    I'm new to vaping and I just need some inputs and suggestions from pros like u guys.😊 

    Mod: paranormal DNA 75 c

    Atty: wasp nano rdta (single coil)

    Current build: dc Clapton wire 26 gauge, 7loops

    What's the best wattage to vape on?

    If I vape at 40w, volts go up to 5.45 

    Ohms at .6 when the coil heats up goes up a bit up to .7 

    Haven't found my vape's sweet spot yet.

    Scared of ramping up the wattage, because the voltage goes high too. 😊

    I also get spitbacks at 35-40w sometimes.

    Build was done yesterday at the local shop.

  13. Preheat in Kanthal - It Works!

    in General Discussion

    Posted

    Hi, i'm new to DNA. I have dna 75c paranormal and hcigar vt75 nano dna. Got 2 attys built in dc clapton wires 26g 7 loops on smm rta and 7 loops on wasp nano rdta both are single coiled atty. I noticed my mod's resistance from.66 jumps to .71 everytime I vape it. I tried using both attys on the hcigar, there it's worse. The jump goes from .60 down to .4 and other numbers. With the paranormal, from .66 to .71 every hit.

     

    I only vape at 40watts on both mods.

    Your answers will be much appreciated. 

     

    Cheers!

    Poj

  14. Ohms jumping a bit while vaping

    in General Discussion

    Posted

    Hi, i'm new to DNA. I have dna 75c paranormal and hcigar vt75 nano dna. Got 2 attys built in dc clapton wires 26g 7 loops on smm rta and 7 loops wasp nano rdta both have single coiled atty. I noticed my mod's resistance from.66 jumps to .71 everytime I vape it. I tried using both attys on the hcigar, there it's worse. The jump goes from .60 down to .4 and other numbers. With the paranormal, from .66 to .71 every hit.

    Your answers will be much appreciated. 

     

    Cheers!

    Poj

  16. USB Connection

    in General Discussion

    Posted

    Thanks Giz for the prompt response. I'll try to configure it on escribe then. I'm getting the "temp protected" error message too on a newly built wasp nano rdta (ss wire 28 gauge) it seems that the only wire it is able to recognize was kanthal 0.4 or 0.5 If the loops were more than five that's when it started to display the temp protected error message and the 0.00 volts sometimes.

  20. Paranormal DNA 75 c 0 volts when firing

    in General Discussion

    Posted

    Hi!

     

    I recently purchased the new lost vape paranormal DNA 75c mod. I just had a new serpent smm single coil atty built by a local shop... while I was vaping on it, it was flavorful and produced good clouds...When I opened the atty I noticed that there were more than 5 loops probably about 8 or 10. Then I took the batteries out as I usually do when I am not using the mod. The next day I tried using the mod then I heard Poppin sound from the atty then the voltage on the screen would indicate 0.00 this is while I was trying to fire it. Now I clearly have no clue what just happened. I need your help guys...Now I am going to a different shop to have the atomizer rebuilt with kanthal at 5 loops as usual with the 3mm guide. See if the mod would behave like it used to...Because I figured that it was the only thing that was done differently on the mod before the 0 volts happen.

×
×
  • Create New...