Jump to content
Evolv DNA Forum

Droopydroors

Members
 View Profile  See their activity

  • Posts

    82

  • Joined

  • Last visited

  • Days Won

    1

 Content Type 

Posts posted by Droopydroors

  1. About Orions that stop responding

    in General Discussion

    Posted

    And just a heads up. In the video he touches the 2 middle solder points to reset it and that did not work for me.  So I basically just touched the big solder joint all the way to the left and one of the middle solder joint and that made a very small spark and then it started working. So you may have to fiddle around a bit with the top of the board touching different parts to reset it. 

  5. Wattage not changing

    in General Discussion

    Posted

    So I found a work around if anyone else has this issue. This was happening with a .5ohm pod so I went in to the "Mod" tab and un checked the "Enable" box above the MTL settings. Then I set the DL Max resistance to 0.695.  So basically both pods will run the same wattage. I have the White set to 11 watts that I will use for the .5ohm pods and for the .25ohm pods I will use the Blue and Red settings set to 13 and 15 watts.  I guess that's the great thing about escribe, even though my device is faulty I can still use it!

  6. Wattage not changing

    in General Discussion

    Posted

    I have 2 Orions and i switched a pod from one to the other and noticed a very different hit between the two. They are both using default settings and on the red light without replay set.  So i hooked the one up to escribe to check device monitor and sure enough no matter what wattage i put in it stays at 8 watts.  I put it up to 15 watts and it only goes to 8.  It seems as though it may be stuck in a replay.  So far i have tried restoring to default settings but nothing changes. Any ideas? 

  7. Replay Issues

    in General Discussion

    Posted

    Also another thing that is an issue maybe.  If you take the pod out and put it back in while its still warm the cold ohms will be alot higher than it should be.   So make sure the pod is at room temperature before turning the device on or putting the pod in.  Im not sure if the cold ohms adjust after a certain amount of time of non use.   Also i dropped the replay "warmth" down to 1 and it seems like its not jumping above the set point.  So maybe this is a quick fix.

  8. Replay Issues

    in General Discussion

    Posted

    Here are some things I'm noticing about replay that are not good in a pod system.   Im sure over time they will be fixed but this is what im noticing now.   So i put a new pod on two days ago.  While using the device with the .25 ohm pod and the blue setting which is set to 13 watts with a 2 watt boost and replay "warmth" ( which still doesnt make sense if its supposed to replay the last hit ) set at 3 I was getting burnt hits.   So just like always i set the device on the middle setting and started hitting it until i got the hit i liked then i put it in replay mode.   But periodically during the day it would just give me a burnt hit which if you are familiar with pods a burnt hit is not good because it will most likely mean you need a new pod even though i just started using this one!!.. So when i got home i hooked it up to escribe and pulled up device manager and it showed the problem on the first hit.  For some reason while in replay it was pushing 25 watts to the coil at start up and dropping to 13 watts after about .3 seconds.    This is way over any setting that i have ever set the device.   So for now i will not be using replay till these issues get worked out because these pods are not cheap and if they are only lasting for 3 days they become expensive!!   So just something i figured would be useful if anyone else is having this issue.

  12. Lostvape Orion DNA Go

    in EScribe, Software and Firmware

    Posted

    I am very happy with the purchase but in my opinion this device is not a nic salt device.  If you run 3mg or 6mg freebase it shines.  Also most of the reviewers that had the device before it dropped were running regular nicotine.  Most of the nic salts on the market are, IMO, shit. They seem to be using extreme amounts of sugar to try and get flavor out of these pod systems. But really all it does is destroy coils. There are 2 things that destroy coils, nicotine and sugar.  So if you are running 25 or 50 nic salts plan on burning through the pods.  I don't think I have seen this being sold as a "nic salt" device anywhere.

  13. Battery?

    in General Discussion

    Posted

    I have to check this on device manager as well.  I let mine charge overnight and when I woke up to leave for work the LED was out.  I believe I read this is normal because the device shuts off the USB after an hour of non use.  But the battery definatley was not charged fully because it only lasted an hour or so.

  14. Lost Vape Orion contacts.

    in General Discussion

    Posted

    Just a heads up to everyone with the Orion.  So I noticed after pulling my pod off that one of the spring loaded contacts was stuck down.  The pods still made contact with it but I imagine some pods may not.  There are two small Phillip screws on either side of those contact pins if you take a screwdriver and loosen them a bit the contact will pop back up.  To stop this from happening when you tighten them back down do not over tighten and the contact will stay lose.  This happened on both of my Orion's.  Also I have one where the pod is VERY snug and will not pop out unless I give it a tug and the other pops out on its own when I pull down the release so it seems as though there are some tolerance issues at the Lost Vape factory. Just a heads up that may help someone else down the road.

    • Like 1

  16. The usb is not a data cable REALLY?

    in General Discussion

    Posted

    15 hours ago, Vape_Like_A_Boss said:

    In case other people see this about the mod not coming with pods, make sure you shop around. I almost bought a device with the mod only, was in the checkout process when I decided to check for other retailers. Sure enough, Vape Royalty sells the starter kit with 2 pods, so I ended up buying it from them for the same price I was paying the other place for the mod with no pods. I'm sure there will be a lot of retailers selling the mod only because that increases their margin, but there will also be many selling a kit with pods, so shop around.

    The reason it doesn't come with pods in the USA is because if it was sold as a full kit a 25% tariff would apply, which would price it much higher.  Be happy it doesn't come with pods because it would be over $100.  All "full" kits , since August 23rd I think, coming from China now have a 25% import tax with parts and component tariff coming soon.

    • Thanks 2

  18. Lostvape Orion DNA Go

    in EScribe, Software and Firmware

    Posted

    1 hour ago, scottyboyus said:

    I contacted Evolvapor and tech support sent me links to download service pack for DNA Go, but they don't work.

    I agree, with 0.5 pod on lowest setting, it is still too much power.

    I think the boost is set too high.  Seems like coil is already burnt with just 1 tank usage.

    Anybody has any luck using escribe with Lost Vape Orion?

    They work and are now posted on these forums.  Make sure NOT to use the cord that comes with the device. It is not a data cord only a charging cord.  Also yes the .5 ohm pods are horrible mine was shot in 3 days possible because even though they say MTL they actually are not. So if you close the airflow down too much they end up burning the cotton. The .25 pods are excellent and I am on a weeks use and it still tastes great.

    • Thanks 1

  20. Escribe for DNA GO

    in General Discussion

    Posted

    3 hours ago, FrankV said:

    Mine won’t come up on Escribe. I have a version just for my 250C but I’m not sure if that’s the same software. Can’t find anything about the DNA Go chip on the first page. Anyone have any help or have the software for Mac? 

    The firmware needed is literally the second post in this thread.

  21. Escribe for DNA GO

    in General Discussion

    Posted

    Just now, WozniakMac said:

    This worked! I got a cable from my Mophie charger and it worked fine. I updated my settings and this thing rocks after the wattage adjustments. Thank you so much!

    Good!!! I'm glad it worked.  It seems very sensitive to cords. I had one cord that worked earlier today and then it didn't work a few minutes ago so I used a different cord that seemed to be a bit more snug and it worked without issue.  I did notify Lost Vape that they should supply a USB data cord with the Orion.

×
×
  • Create New...