-
Posts
39 -
Joined
-
Last visited
-
Days Won
8
Content Type
Profiles
Forums
Downloads
Posts posted by eucalyptus.
-
-
Hello.
I obtained DNA60SS.
I reviewed it in the range that I understand.
We hope for your reference.
However, it is Japanese.
-
Hello.
The same happened when trying themes using external fonts.
When the theme PC and the eScribe PC are different, there is a font with the same name, it is likely to occur if the font width is larger than the theme setting.
I solved the problem by writing a standard theme.
But my screen was what happened with "MAIN".
I pray for your board to heal.
-
I also present an example of a connection.
I use old DNA 60.
It is the one when examining the board replacement for Clone Mod for testing.
I am sorry, Japanese.
- 1
-
Thank you for your response.
I am sad that symptoms have occurred on my board, but it is good news that I found a bug earlier and that I can improve with software.
However, since it is a problem related to the battery end voltage, I urged the firmware update. -
Hello.
eScribe -> Theme Tab -> Theme Designer -> Language Tab -> Locale : Date (M/d/yy)
ex)
17/6/8 : yy/M/d
17/06/08 : yy/MM/dd
17-06-08 : yy-MM-dd
-
Hello.
For your information...
JST B2C Connector pitch variations.
SH : 1mm
ZH : 1.5mm
PH : 2mm
XH : 2.5mm
DNA60 USB Through-hole pitch : 0.08 in ( approx. 2mm ) = PH Connector!.
-
Thank you very much. I will check it immediately.
-
-
-
Thanks for reply!.
I have examined it in more detail.
1. F/W
I tried reinstalling Rev 19 and Rev 20, but there was no change.2. Current
I compared it with a new board.
· High current consumption
· Low end voltage (approx. 1.2V)
· It does not become standby
Therefore, not only F/W but also element failure is suspected.Attach the measurement result.
Oscilloscope: rigol DS 1054 Z
Voltage source: DDC
Current probe: Hantek CC-65tr_standby.png: trouble DNA75c standby
tr_endv.png: troble DNA75c end-voltage.
nm_standby.png: New DNA75c standby.
nm_endv.png: New DNA75c end-voltage.
-
Hello.
My board is currently experiencing problems.
That is the discharge of the battery.
1. The board does not enter sleep mode
* In the non-charging state, the batteries decrease when locking and not locking.
* VTC4 It has changed from 99% to 70% by leaving for 2 hours.
* USB connection, board is generating heat even in non-charging state.
2. The board will use the battery until the end voltage of the battery.
* If left unattended, I will use the battery until it is empty.
* About 0.9 V or so.My board was not originating from the beginning.
Perhaps, after doing "restore default", it seems that a phenomenon is occurring.My board does not use production utility.
The default setting is the initial state.
Items other than "Theme" are not operated.Board Information:
Evolv DNA 75 Color
Device Information
Serial Number YBAK FGEW PKWY
Production History
Friday, April 21, 2017, 3:53 PM
Board programmedRevision.20.
Thank you.
-
Thanks for Implementation!.
-
Hello.
Thanks,for reply!.
When a short circuit is detected, it forcibly shuts off and a click sound is emitted from the board. Since it seems to be a malfunction at first glance, I expect it to heal. However, because it is not a fatal factor, priority is low and it is OK.
-
Thank you for your reply.
510 The connector is removed once it is confirmed.
Resistance value between ATM and GND is about 500 ohms when the board is not connected and nothing is connected.
Since this value is almost equal to normal DNA 75, it is judged that it is not physically short-circuited.
-
Hello.
My DNA 75C is "short" when remove the atomizer.
After resetting, it becomes "CHECK ATOMIZER" before attaching the atomizer.
I examined it with ATOMIZER ANALYZER, after removing the atomizer, the value of 100 ohms or more appears.
My MOD is actually not short-circuited.
Is there a problem with my board? .
Revision:20
Theme:Default Theme. ( "Factory Setting Reset." )
-
UPDATED!.
KIRBYTHEME 1.1:
*ohms param.
*diag message.
*wallpaper.
*"puff" picture.
*"enemy" picture.
*board picture.
*sleep & charge picture.Note:
When "Flash Puff", the status is 0.
Please try longer. -
Hello.
I am glad you liked it.
I will post it.
Thanks.
-
- 1
-
- 1
-
Hello.
DNA75C has arrived.
I made MOD.
Comparison with DNA 75 and summarized the points I noticed.
If it is helpful.
However, it is Japanese.
http://ecig.eucaly.net/archives/15506415.html- 6
-
Japanese translation for Escribe 1.2.
#tooltip translation is deleted. -
DNA60 Review!.
at japanese.
http://ecig.eucaly.net/archives/5040190.html -
You are at rebuild, do you remove atomizer?
Since I combination is fixed , and as it is rebuilt.
So effortless.
-
Hello.
"Temp Adjustment mode" added on eScribe 1.0.42.
Likewise "Voltage Adjustment mode" setup on Profile?.
#Show Voltage on big screen. + / - adjust voltage. Watt and Temp Control is Off.
Likewise "DRY BURN mode" setup on Profile?.
#Show Ohms on big screen. + / - adjust watt or voltage or temp.
#Enhanced time protection setup (15sec/20sec) more better!.
Likewise "COIL SETUP mode" setup on Profile?.
#Show Ohms on big screen. +/ - is off.
#Puff trigger : 1W / 0.1sec. sense coil reg.
#measurement ohms on screen. hold display (until sleep).
usecase :
a.setup "DRY BURN MODE" on profile7.
b.setup "COIL SETUP MODE" on profile8.
c.adjust DRY BURN MODE Power and time protection on profile 7.
1.Dna Function "power lock mode".
2.Push +/- button select "profile 8".
3.coil setup and check ( push puff ).
4.Push +/- button select "profile 7".
5.dry burn ( push puff ).
6.select profile 8 and 7, make coil!.
#like "tab 521".
Control demo of evolv DNA Series by Python
in Researcher Forum
Posted
Hello.
I made an LED panel that uses Raspberry Pi to output information from DNA.
I am using Python for control.
https://github.com/eucalyhome/dnainfo