-
Posts
63 -
Joined
-
Days Won
1
Content Type
Profiles
Forums
Downloads
Posts posted by Guy Nicolson
-
-
If you completely turn off the iPhone before charging, it will turn back on when you plug it into the charger.
If its on when you plug it in to charge, the battery symbol at the top right corner will turn green to indicate its charging.
Additionally the lock screen will show the battery percentage followed by the word "charged" under the clock.
I get none of the above when using power bank OTG to charge my iPhone with a frequently used lightning cable and an alternate tested and working lightning cable
After setting up a screen with a toggle for each the mod shows it is connected and discharging
AUTOMATIC
POWER BANK MODE ENABLED
BATTERY DISCHARGING ( POWER BANK)
CONNECTED AS POWER BANK
-
Set up a page for OTG Power Bank with all the toggles and info I could see to use
I can charge a power bank using micro USB but not charge my iPhone using a cable that I regularly use to charge that.
This tells me the OTG adapter is working. Maybe it's the current level from the mod that is the problem?
-
I would like to use the power bank function with my mod as it has massive lipo haha
I've tried using auto in the display tab with no success
Using a toggle does not activate the power bank function on mine
I do not know how to configure a screen dedicated to the function yet
I have been using a newly bought USB OTG to USB 2.0 adapter and a tested micro USB cable that charges this DNA250 colour @ 2amps
Escribe Version: 2.0 SP15.1 on a MacBook
Any advice would be much appreciated
USB On-The-Go
The DNA 250C supports USB On-The-Go. An OTG adapter may be plugged into the Micro USB port on the device to charge any other device capable of charging via USB. By default OTG charging must be toggled on manually from the device. OTG charging can be configured to begin automatically using the Power Bank option in EScribe on the Display tab. OTG charging will not over-drain the DNA 250C.
-
-
Hello @ChunkyButt200
Your explanation makes total sense and is very helpful. Knowing buck only topology draws 32amps max is good to know. I will monitor higher wattage levels and see what's what. Thanks for the quick response
-
I have a couple of questions regarding Lipo pack settings for my DNA250C mod
I have calculated that the Turnigy nano-tech 2200 mAh 4s lipo which states 25c constant 50c burst as 2200*25 /1000= 55amps and 80% of that = 44amps
I'm using 45 amps for my max sustained output current and 55amps for Max peak current
Is this too cautious?
Max peak input and max sustained input I would like advice on what to set these as well please
-
My device turns on after Case Analysis
I still do not know why the first Analysis gave those numbers, maybe the new lipo reaching proper balanced state as cell 3 was not in line with 1,2 and 4 at first, It was balance when I ran the first analysis though
1 amp from my Macbook
Nothing else thank you
-
No suggestion from Escribe about the mods case static temperature rise this time
It's been interesting
-
Good you are back
Yes I'm on that version as well
-
Bug?
-
All tests have taken place in the same position in the same room
I'm going to run it again with the door on at 50% charge and see what I get this time
-
Case thermals run again no door
50% charge 71.5℉
Turnigy nano-tech 2200mah 4S 25~50C Lipo Pack
Spec.
Capacity:2200mAh
Voltage: 4S1P / 4 Cell / 14.8V
Discharge: 25C Constant / 50C Burst
Weight: 218g (including wire, plug & case)
Dimensions: 100x35x30mm
-
Ok I'll run it again
-
Hello
Battery was @ 25%
Temp reading taken from a thermometer in the room with an out probe positioned to give 2 readings
Yes I will run it again with the door off
Do you think it's the enclosure and lipo size?
-
I have run case thermals for this mod and Escribe suggests this
It was left overnight to reach ambient temperature before running case thermals
Internal resistance has been measured @ 0.005Ω
New Turnigy nano-tech 2200mah 4S 25~50C Lipo Pack
Any advice would be appreciated thanks
-
I have run case thermals for this mod I built 3 times and twice I have been given this warning.
It was left overnight to reach ambient temperature before running case thermals
Internal resistance has been measured @ 0.005Ω
New Turnigy nano-tech 2200mah 4S 25~50C Lipo Pack
Are the dimensions of the mod enclosure resulting in these figures and warning? It is quite large and made from billet aluminium.
Any ideas would be appreciated thanks
-
Turnigy nano-tech 2200mah 4S 25~50C .csv
-
1
-
-
SOME NEW SCREENS ENJOY
-
1
-
-
Running 10.9.5 OS X
DNA 60, DNA200 and DNA250 working
Service pack applied to DNA200 1.2 SP5
Thank you for all your efforts
-
1
-
-
Beta 9 with OS X 10.9.5 DNA 250 no problems
Thank you
-
1
-
-
Maybe temperature when it was put together perished the Oring? My Alpine RDTA's O-rings were stuck fast to the glass once I managed to get the bottom of the tank off might have been temp also. Who Knows weird one.
-
Mine had no funky tastes and was really clean out the box. I've never heard of metallic taste from a Siren being common from the groups I'm in so...
Out of the box with a perished O-ring does not sound good, I'd use your spares and change them all out just incase they were contaminated at the factory and that has caused them to perish. Not wanting to overreact or anything better safe than sorry
What wire type are you making your coils from ?
-
Siren GTA screen
-
Hello,
I'm running OS X 10.9.5 and version b6 US of Escribe
I have uploaded custom screens to my DNA 60 and saved custom screens to my Mac successfully
I adjusted and uploaded/downloaded the value for Temperature and changed CoilMaterial (upload/download)
Looks great thank you for making a Mac version possible it's very much appreciated.
Power bank functionality
in General Discussion
Posted · Edited by Guy Nicolson
Thanks @ChunkyButt200 now I know why, I feel better haha