JaI Haze

I tried it in both wattage and temp mode. I even tried doing a factory default which wiped everything. I find it strange its when I flip the batteries around slot 2 to slot 1 or a new battery swap out it lowers the count. Heres the funny thing, when it lowers the count ONE TIME it wont do it again for that swap out. Like if I put fresh batteries in it will lower, I take them out and put another new set in it wont do it. Now if I hit it ONE time with new batteries and replace the brand new ones I just put in it lowers the count again. I have no idea why it does what it does

Same Bill

Relo doesnt do it, its only dual battery or single battery mods

tried it. Same thing. It lowers it everytime. And keep in mind the chip thats in it is a brand new one I got from evolv

yeah i have tried this on every 2 battery and single vt75. vt133 does it every now and then, the boxer EVERYtime. I have 2 welcome screens as well. The hit count i tried moving it aroud and even tried removing it from the screen and its the same result everytime. No idea why its doing that. I have 2 boxers and they both do it everytime

https://www.dropbox.com/s/buhazpa72jenovz/Video%20May%2031%2C%204%2032%2032%20PM.mov?dl=0 theres a video

Why is it when a DNA75 or 200 uses external batteries when you take them out the puff count loses a good amount on the screen. I dont know why its doing it aside from not having an internal memory to remember where it was at. I cannot seem to get this to work properly and show all the times with accurate numbers. I checked this about 5 times with 4 different mods and different firmwares

wait a few minutes like when screen shuts off? No matter what I do it ALWAYS removes X amount of puff from the display and the memory. This is definitely a bug with the external battery dna's

Ok I checked it on 4 different devices with external batteries. It truly is resetting the puff count from 50-200 each time i take batteries out. EXCEPT the Wismec DNA, why is this. The DNA75 and 133 it happens on

yeah apparently its an issue with some DNA chips. Very awkward.

i tried everything even installing OLDER firmware. Nothing is working. So I just sent them the boxer and a new DNA chip I bought from evolv. Sucks but whatever right

yeah i tried it. No dice. Its weird it works perfectly fine after jumpstarted with usb

yeah i saw this one /topic/67027-topic/ how do you do a HARD reboot

Ok so quick question. This sounds really weird and I dont know what would be causing this. I have a brand new dna installed from Ginger Vaper as my fuse went on my old one. The issue I am having now is it WORKS fine after it wakes up via usb. When it goes back to sleep it wont turn the mod back on until I wake it up with USB. What would cause this?

is that the firmware thats current or the beta one? I have the firmware that came with the DNA75 download and that apparently upped the max power to 9.2V

I was wondering when playing around escribe I saw If temperature sensing coil is sensed, what if I set this to kanthal and did a pre heat punch. Would it theoretically work or is it only working on the DNA boards for temp metals? I am asking because I would love for it to pre heat higher than set power. Sig213 does this very well and was hoping if I could get my dna's to do this

http://evolvapor.com/dna75.php i found this but the escribe is the same for some reason

I was one of the first people to have the DNA75 sent to me by hcigar and i cant seem to find the software for it.

Ok I had my DNA on the side of a table and it got knocked off on to the floor (which is carpet btw) and then when I went to turn it on, IT ONLY turned on when I held the button down. Also when I plug it in the screen lights up. The issue I have though is its NOT when not plugged in working. Could one of the solder joints be bad? I checked them visually and they all looked good

i have it displayed on the screen, I havent cross refrenced it with the ecigstats yet, just bothers me it lowers. I know its superficial but I like to get it maxed out

ok double checked this today after removing battery for 8 seconds it happens. I am really confused as to why this happening

I am wondering if anyone else is having this issue. I have the boxer 133 with the latest firmware and even tried the beta firmware. But when I take out a battery (18650) and put a new one in it lowers the puff count. This is something I love about the DNA200. I am confused why the Releaux, Hana and VT didnt do this but the one where the batteries come out are. Is there like a resetting option since it looses all definitive power when a battery comes out it resets to the last time it REMEMBERs it?