Yurlosin Posted July 23, 2015 Author Report Share Posted July 23, 2015 Using a turnigy nanno tech 950mah 3s when I plug the charger in the screen brightens up but doesn't show the charging sign if I upload the same factory settings to the device it will charge but unplug it and plug back in won't charge again I'm lost on this one Link to comment Share on other sites More sharing options...
macz Posted July 23, 2015 Report Share Posted July 23, 2015 Yurlosin said:Using a turnigy nanno tech 950mah 3s when I plug the charger in the screen brightens up but doesn't show the charging sign if I upload the same factory settings to the device it will charge but unplug it and plug back in won't charge again I'm lost on this oneCheck the Charging Brightness in Screen tab on EScribe, if 0% set to at least 35% or higher for it to show up Link to comment Share on other sites More sharing options...
Yurlosin Posted July 23, 2015 Author Report Share Posted July 23, 2015 The screen stays on just doesn't charge the battery if I force a soft reset it will charge again but as soon as you unplug the USB and plug back in it won't charge again Link to comment Share on other sites More sharing options...
Yurlosin Posted July 23, 2015 Author Report Share Posted July 23, 2015 also will not fire when plugged in says check atomiser. unplugged it works fine i have noticed that it asks if its a new coil when you unplug it Link to comment Share on other sites More sharing options...
Yurlosin Posted July 23, 2015 Author Report Share Posted July 23, 2015 This is the first of 5 boards I have hopefully the others don't have the same problem Link to comment Share on other sites More sharing options...
Yurlosin Posted July 23, 2015 Author Report Share Posted July 23, 2015 Correction it says check battery when the fire button is pressed while usb is plugged in Link to comment Share on other sites More sharing options...
John Posted July 23, 2015 Report Share Posted July 23, 2015 What cell voltages are you reading in device monitor when you try to fire while connected to USB?Also, what firmware revision? Link to comment Share on other sites More sharing options...
Yurlosin Posted July 23, 2015 Author Report Share Posted July 23, 2015 it has the newest firmware porblem is getting worse last night it read all 3 cells now it is not reading cell1 at all so it will not power up on its own only thing i did was leave it connected to the charger all night i have tried swapping the battery to another board that works fine no luck there maybe a bad trace in the board? Link to comment Share on other sites More sharing options...
John Posted July 23, 2015 Report Share Posted July 23, 2015 Could be. Picture of the board in question? Link to comment Share on other sites More sharing options...
Yurlosin Posted July 23, 2015 Author Report Share Posted July 23, 2015 Let me know if you need any closer pics Link to comment Share on other sites More sharing options...
John Posted July 24, 2015 Report Share Posted July 24, 2015 Yep. If you look in the upper right corner, there are components that got knocked off. PM me your address and I'll swap you for another. Link to comment Share on other sites More sharing options...
Yurlosin Posted August 2, 2015 Author Report Share Posted August 2, 2015 John this is the first board I mentioned in the other post Link to comment Share on other sites More sharing options...
Protocol-X Posted September 25, 2015 Report Share Posted September 25, 2015 Could you point it where they are missing? I have the same issue and tried everything. Link to comment Share on other sites More sharing options...
Brandon Posted September 29, 2015 Report Share Posted September 29, 2015 Link to comment Share on other sites More sharing options...
Adrian Posted April 28, 2018 Report Share Posted April 28, 2018 Got same problem doesn't recognise usb in escribe or for USB charging.have tried everything and usb went wrong 4 weeks after getting mod and just had new screen and lipo fitted but usb still no good Link to comment Share on other sites More sharing options...
James Posted April 28, 2018 Report Share Posted April 28, 2018 @Adrian, you'll want to contact the Help Desk: https://helpdesk.evolvapor.com Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now