Noixd Posted September 7, 2015 Author Report Posted September 7, 2015 Great mod but having two problems with this device in TC mode. First problem is that when I press the fire button it sometimes doesn't produce any vape. I have a nickel clapton reading at .07ohms at 450F @70W and randomly when I press the fire button the screen says 800F at .01W. I put the same atty on my opus200 and hanamodz v200 and it works perfectly fine. If anyone has had the same issues and know what the problem is that would be great to know. The next problem is that in TC, the device is not reading the resistance correctly. The same build from above would always ask me if it's a new coil at .15 ohms. While I vape the resistance reading keeps increasing to .10,.13 and .15. I think it's ground issues with the 510 connection. I know it's not my builds bc when I put the same atty on my Opus200 and Hanamodz V200, it reads properly at .07ohm and it never fluctuates. Does anyone else who has a VS DNA200 see that their board was customized in Rhode Island?
Brandon Posted September 8, 2015 Report Posted September 8, 2015 Sounds like an increasingly poor mechanical connection. Did you check the VS's center pin? I've had mine stick down before but that's likely due to the fact that I'm a sloppy dripper. I also noticed that their 510 connector is quite deep, perhaps the atty you are using is just barely able to reach the center pin. Check it in atomizer analyzer.
Noixd Posted September 8, 2015 Author Report Posted September 8, 2015 Brandon thanks for the response. I'm pretty sure it's due to the deep 510 center pin. I have the same build on my Petri and Origenny but those seems to be read at the proper resistance. Only my velocity and marquis are giving me problems but when I put it on my opus and Hana it doesn't give me any problems. When I put the velocity and marquis in the atty analyzer, it gives me higher than normal resistances or sometimes an error message.
Brandon Posted September 8, 2015 Report Posted September 8, 2015 Yeah, it sounds like those 2 are having trouble making a solid connection. I spoke with their tech support a few minutes ago and made them aware.The problem really resides in the lack of a standard 510 connector spec industry wide.Edit: for clarification
Noixd Posted September 8, 2015 Author Report Posted September 8, 2015 Spoke with VS and sending it back to have it looked at by their techs. Great customer service!!! Brandon said:Yeah, it sounds like those 2 are having trouble making a solid connection. I spoke with their tech support a few minutes ago and made them aware.The problem really resides in the lack of a standard for 510.
llkoolj Posted September 29, 2015 Report Posted September 29, 2015 I have had pretty much the same experience even when using various tanks such as freemax , crown and kangwer subtanks , basically intermittent firing causing no vape production.I have just e mailed vapor shark support so watch this space....
llkoolj Posted October 1, 2015 Report Posted October 1, 2015 Great customer service but I will need to send DNA 200 back as they believe its a problem with the board
Hipo236 Posted October 25, 2015 Report Posted October 25, 2015 i have a problem with my DNA 200 it is giving me a mesage (battery unbalanced) and it stops firing!!!does any one has a solution
AGoyer001 Posted October 25, 2015 Report Posted October 25, 2015 My vs 200 won't hold a warm vape.. I get 6-10 good hits then it goes to cold vape, I change to a different profile and it's good again.. Having to toggle back and forth is nuts though. I'm thinking its a bad unit
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now