Dragan Čelebić
-
Posts
10 -
Joined
-
Last visited
Content Type
Profiles
Forums
Downloads
Posts posted by Dragan Čelebić
-
-
13 hours ago, Wayneo said:
Hopefully it is still under warranty from where you purchased it. I think you should either contact them or the builder himself.
Failing that, you could open it up and look around the screen connector itself.
If neither of those 2 options seem reasonable, you could open an RMA with Evolv.
I imagine the screen is very close to the board, and you might want to purchase a data/charging board for future use, such as setting the board up to your liking. Checking the firmware level, etc. Those board pins are at the bottom of the board near the screen ZIF connector.
I made this cable that is removable just for the above changes.
After all that I posted a cheat sheet for these non color boards.
https://forum.evolvapor.com/topic/71559-cheat-sheet-key-combos-for-non-color-mods/
Thank you my dear friend Wayne, Very useful information from you. I will record everything, but still, the display is not correct. I'll send it to the service. Thanks again. 🙂 -
13 hours ago, retird said:
You might contact Visionary Mods especially if less than 30 days old. See if they will help you. Nice mod by the way....
The mod was purchased in March this year in Croatia. I contacted the seller on the messenger. He accepted the complaint. Tomorrow I'm sending a moder from Visionary. I am from Serbia. 🙂
-
6 minutes ago, retird said:
If the screen gets crcked it can go black. Any signs of a crack?
well no,I watched in the bright light. Nothing is noticed, there are no cracks. everything was working normally, only, at one point when I looked below, at the screen, I noticed it wasn't working. and, I'm just sad.
-
47 minutes ago, Dragan Čelebić said:
I'll try right awayUnfortunately, even after countless attempts, it won't, there are no lights on the screen. -
3 minutes ago, dwcraig1 said:
If pressing the fire button 5 times puts it in to lock mode and it then says "Locked, Clicked 5 times" and you can see that OK then the mod is in stealth mode. Stealth mode is turned on/off by first locking fire button by pressing 5 times. When locked hold fire button and down button at the same time to turn stealth mode on/off.
I'll try right away -
NYMFA DNA60 BY VISIONARY MODS, no usb port. How can I adjust the brightness of the screen? Today, during normal use, the screen is completely darkened. The mode works, but there is no light on the screen. Is there any help?
-
3 hours ago, Apar said:
Not working for me, when i plug my mod, it's written "No compatible USB devices are connected. To continue, please connect one. If one already IS connected, try unplugging and plugging it back in. The cable may be loose." Please help.. 😟
I had the same or a similar problem when I got my hyperion DNA 100C.
The first thing I noticed was that I didn't hear the "bling" sound that is heard when a device is connected to a computer via a USB cable. I kept going. I installed EScribe and had the same problem "I don't have a compatible device connected". I installed SP 27. I still had the same problem. He doesn't recognize. I had a few USB cables from different mods in the house. Eureka. I heard a "bling" sound. and the program recognized my DNA 100C. Everything else is history.Thanks for reading.
-
I will try to help with the requests.
My settings for Molicel P42 are as follows:
Cell Soft Cutoff: 2.9V
Max Peak Input Current: 28A (1 s)
Max Sustained Input Current: 18A
Max USB Charge Rate: 1.5A
Attachment, my Molicel P42A Profile.
Thanks
Molicel P42A Profile
in Batteries and Charging
Posted
Hello Patricio Fernando ..mainly protect the battery cells and contribute to the preservation of the board (my view)