[TC not working on Thelema]

19 minuti fa, retird ha scritto:

Most folks use the Watts profile but you can use the TC profile.  Just a note.... The Temp Protect message usually just means that you have reached the set temperature and thus not usually an error message.

Is there a reason why one would use Watts instead of TC?

[TC not working on Thelema]

EDIT: CASE CLOSED

I tried to tighten the positive pin and now it works perfectly, reaches all temps without issues. Thanks @retirdfor the heads up and thanks Wayneo for all your replies.

Just one last question, can I enable replay with TC? Or is it only for Watt mode?

[TC not working on Thelema]

I have done a few more tests now after the box had been sitting for a whole afternoon by itself while I was out. I input the new room temp Ohms and now the box doesn't give me the temp protected msg anymore, which is a step forward, but now it only reaches 150C instead of the target 220C. No matter if I increase or lower the watts, it keeps firing at max 150C.

Here are my tests:

Minimum temp (93.3C), 30W: Steady 94C @3Watts

150C, 30W: Pretty steady 150C

200C, 30W: Stays on 150C

200C, 40W: Still barely higher than 150C

 

I'm using Profile 7, I added 316L wire material from Steam Engine. With Profile 6 I have even lower temperatures (last tests gave me 141C).

[TC not working on Thelema]

5 ore fa, Wayneo ha scritto:

Can you check the stability of the cold atty/coil in escribe by using 'Atomizer Analyzer'. You should see very small fluctuations in the resistance (.002 - .004Ω) as low power is applied. Let me know.

Is this that same mod you had issues with that off center 510 and check atomizer issues?
Have you ever vaped in TC before?
 

I checked the atty with Escribe and I do see some fluctuations (.489->.491->.488->.492->.493->.487->....)

Not the same mod I had issues with the off center 501/check atomizer. I returned this one and bought a second one from a different retailer.
Never vaped in TC before.

 

@retird How can I check that?

[TC not working on Thelema]

Yeah I did let it sit and measured the coils at room temperature, but still no luck.

It's my first time vaping TC with this mod.

[TC not working on Thelema]

I'm using a wasp nano RDA with 26 AWG SS 316L. I made 3 different coils (plain spaced wire with 6 wraps, 2.5 diameter @~.4Ohms) and at first the mod fires at around 80-90C instead of 220 that I input, then after 3/4 puffs it says "Temp protection" and stops firing altogether. Am I doing something wrong?

[DNA 250c can't measure atomizer Ohms]

47 minuti fa, dwcraig1 ha scritto:

Have you tried other atomizers?

Some 510's on atomizers are on the short side as there is no standard for them.

Does the 510's positive pin appear farther down than usual?

Thanks for your reply. I did try a total of 3 atomizer, but none of them are being recognized by the Thelema. I tried the Geekvape Zeus (subohm), the Zlide and the SMOK TFV12 Prince. All the mentioned atomizers work on my SERIES B DNA75 flawlessly, so I don't think it is a problem with the atomizers.

As for the 510 it doesn't appear farther down than usual, actually it kind of looks a bit taller than my other mods, but I may be wrong. The only thing that may stand out is the fact that the pin is a bit off centered.

[DNA 250c can't measure atomizer Ohms]

Can anyone help me? I just bought a Thelema 250c, but it doesn't recognize any atomizer's Ohms. The box says "Check atomizer" and in Escribe it says "Failed to measure coil Ohms."; Ohms on the box stay at 0.00.

Is it a known issue?