ajoe
-
Posts
25 -
Joined
-
Last visited
-
Days Won
1
Content Type
Profiles
Forums
Downloads
Posts posted by ajoe
-
-
This error has happened on other brands of mods as document on these forums, so it is unlikely a device issue.
Please put in a support ticket in with Evolv. In my experience, they respond in 2-3 days and are very helpful.
-
Have any of you put in a support ticket with Evolv?
It may take a day or two for them to respond, but they are very helpful.
-
1 hour ago, retird said:
...I would like to go to the link you saw.....
Sorry, no idea which links it was. For privacy reasons, my browser deletes everything (including history) each time it quits.
-
16 minutes ago, retird said:
Did a 20 minute google search and haven't found anything YET ...
Do a search for "ijoy diamond temperature control" and there ya go.
-
On 7/31/2018 at 4:56 AM, DJT said:
Anyone else really disappointed with the 250C?
I certainly was until I switched back to TC mode.
I purchased my DNA250c devices specifically after watching an interview with Brandon where he described Replay and mentioned that he had switched to using it exclusively.
But several weeks of using Replay on two devices from different vendors, resulted in frustration from all manner of weird behavior and error messages. Some of those have been reported to Evolv.
After switching back to TC, I'm a happy camper. Great vape, no problems whatsoever.
IMHO, Replay is a great idea that still needs a lot of work.
-
If the connector is accessible, I would try carefully squeezing it with needle nose pliers to tighten the connection.
Other than that, wait to hear from Evolv or solutions from other users.
-
1
-
-
On 6/25/2018 at 6:40 PM, Ellex80 said:
Which coils are replay compatible ?
I´m very interested in X3-Mesh and Dm-Mesh Coils
I am curious if you tried these for TC or Replay. I searched high and low and could not find any information about the coil material. However I have seen references to using them in TC devices, so I assume they will work in Replay.
-
8 hours ago, Gus McNasty said:
For some reason my boaz doesn't work on my paranormal 250c
Does it not fire at all? Perhaps the 510 connection is too short.
The 520 connector has a slotted screw which may or may not mean its length can be adjusted.
So if you are not getting any power to the Boaz, you might contact AVS to see if that 510 screw is adjustable.
-
26 minutes ago, retird said:
..... Which mod is that?......😊
Pretty sure that is a Boxer dual 20700 with squonk.
-
3 minutes ago, Bapo said:
Thanks for the reply. I submitted a ticket as reccomended. The line has something to do with the strength and length of the Puff. The stronger and longer it is, the more the line moves to the left of the displayed graph. If the puff is ever so slight, the line does not display. Go a little longer and stronger, and the line just starts to appear at the right edge of the graph. Go even a little longer and stronger, and it moves a little more to the left. That is the only correlation I’ve been able to determine.
I just checked my device and I can see two such lines if I keep the fire button depressed after a puff so I can see the screen. They divide the screen in thirds.
Not sure if it is connected to your problem though.
Yours does sound like a software problem to me. Are you running the lasses firmware?
-
8 hours ago, ajoe said:
Yes, have ordered from Element with problems.
Yes, the battery door is fixed. I run a rotation of VTC6, HG2, & 30Q without any gaps.
Sorry for the typo: That should have said "Yes, have ordered from Element without problems."
-
I can not help you, but there have been other threads here with people experiencing horizontal lines at about the location of the blue line in the graph on your screen.
As I recall, one person resolved it by replacing the screen. Others where hoping for a firmware fix, but I don't recall that ever happening.
I would submit an Evolv Support Ticket and ask for guidance.
-
14 minutes ago, retird said:
Are you taking an atty off of another device and putting it on the device while the atty is still warm?
You might try this and see what the results will be....:
Create a Profile for each atty using Replay..... Use each Atty with it's corresponding Profile.....
In at least 90% of the occurrences, it is a room temp tank or rda off the shelf.
Creating atomizer profiles wouldn't work for me, and should not be necessary. I have too many duplicate rdas that get interchanged throughout the day to change flavors. That would be a bookkeeping nightmare.
I am willing to try new things but atomizer profiles seems an unnecessary burden when this appears to be DNA250c problem.
And, just for the record, I have also submitted a support ticket.
If you do a search here on "Temp Protect" you will find other similar behavior has been encountered, although perhaps not as well documented. I only because concerned this was a DNA250c problem upon buying my second device and having exhibit the identical behavior.
All that said, thanks for the reply. It never hurts to pursue different avenues of resolve.
-
I have two DNA250c mods; a Lost Vape Triade and Boxer dual 20700 squonk. Both frequently exhibit the same problem.
First of all, I only use SS316L coils in my RDA or Tanks. All of the coils and wire are from the same source. I am using the default theme on both devices.
I always run Replay. This problem occurs when switching atomizers. After the device asks if it is a new atty and I answer yes, any attempt to fire it will result in a Temp Protect message at the bottom of the replay screen. No adjustments to the atomizer or the device setting will correct the problem.
However, sometimes if turn the device off and back on again (5 clicks), it works normally again. If that doesn't work, removing and installing the batteries will clear the error and it will continue normal operation. This does not happen every time I switch atomizers, but approximately 30-40% of the time.
It appears something is happening in the DNA250c that causes it to get confused when changing atomizers.
Any thoughts?
-
Is the DNA250c smart enough to match different brands of batteries to the corresponding CSV file?
For example, I charge all batteries externally and rotate between sets of VTC6, HG2, and 30Q. When I take out the VTC6s and put in the HG2s, does the DNA board automatically switch batter profiles?
I am not having any problems with battery levels, but don't normally pay much attention until they reach 50-60%. Just curios since it is somewhat related to the OP's question.
Thanks.
-
The Boaz RDA they make is also pretty nice,
They also have a current deal for 35% off spooled wire.
-
1
-
-
A properly configured DNA device should never emit any kind of sound.
I would opem a suppor ticket: Evolv Support
-
Connect your device to eScribe, a nd it will let you know if firmware is available.
-
On 7/18/2018 at 5:00 AM, maximumsport said:
Who has ordered from Element or any other retails? Did they fix the battery door on the retail one with no gaps when closed with batteries installed? I know on some reviews the door had a gap when installed with batteries. Just curious if this was fixed with retail versions.
Thanks
Yes, have ordered from Element with problems.
Yes, the battery door is fixed. I run a rotation of VTC6, HG2, & 30Q without any gaps.
-
I have used most of the SS316L coils and wire that Advanced Vapor Supply makes, and they have all worked perfectly in Replay mode.
Additionally, all of their wire is made in the U.S., is very clean, and of very high quality.
They also make some 430SS products specifically for Temp Control, but I have no experience with that particular SS wire. It is only recommended for advanced users.
They are located in Colorado. Advanced Vape Supply
No affiliation, just a very satisfied customer.
-
In that case, if you are in the U.S., here is the phone number: 562-998-8068
If that doesn't help, I would be wanting my money back from wherever I purchased.
You could dispute the charge with your credit card company based on the company not fulfilling their warranty obligation.
Good luck.
-
I have two DNA250c devices from two different manufacturers, both are running the default Evolve theme.
I have never seen this behavior.
Do you have a custom theme installed? If so, perhaps reverting to the default theme would help.
I checked the Escribe docs and can't find any settings to control such behavior.
Sorry I can't be of more help. Maybe someone else has run into this.
-
Have you talked to the manufacturer?
Giner Vaper gives you a 6 month warranty. Given the number of problems, this could be an assembly problem and have nothing to do with Evolv.
Get it fixed or replaced by Ginger and move on.
-
Thanks clivy,
I really like my Riftcore Duo and have a 250c on order. Good to know I can try out replay.
Dna 250c and Drop RDA
in General Discussion
Posted · Edited by ajoe
I use 40 / 450 for TC in my Drops with SS alien coils and get great flavor. I have 3 for juice testing that are in constant rotation.
For flavor, I would suggest single or dual coil. Too much heat from a quad could be killing the flavor.